NX3V1T66GW,125 NXP Semiconductors, NX3V1T66GW,125 Datasheet - Page 4

• Manufacturer Part Number: NX3V1T66GW,125
• Description: IC ANALOG SWITCH SPST UMT5
• Manufacturer: NXP Semiconductors

Specifications of NX3V1T66GW,125

• Number Of Switches: 1
• Switch Configuration: SPST
• On Resistance (max): 0.8 Ohms
• On Time (max): 57 ns
• Off Time (max): 90 ns
• Off Isolation (typ): - 90 dB
• Supply Voltage (max): 4.3 V
• Supply Voltage (min): 1.4 V
• Supply Current: 690 nA, 800 nA
• Maximum Power Dissipation: 250 mW
• Maximum Operating Temperature: + 125 C
• Mounting Style: SMD/SMT
• Package / Case: TSSOP-5
• Minimum Operating Temperature: - 40 C
• Off State Leakage Current (max): +/- 500 nA
• Operating Frequency: 25 MHz
• Power Dissipation: 250 mW
• Switch Current (typ): +/- 500 mA, +/- 750 mA
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Other names: 568-5568-2

NXP Semiconductors
9. Limiting values
Table 5.
In accordance with the Absolute Maximum Rating System (IEC 60134). Voltages are referenced to GND (ground = 0 V).
[1]
[2]
[3]
10. Recommended operating conditions
Table 6.
[1]
[2]
NX3V1T66
Product data sheet
Symbol
V
V
V
I
I
I
T
P
Symbol Parameter
V
V
V
T
t/V
IK
SK
SW
stg
amb
CC
I
SW
tot
CC
I
SW
The minimum input voltage rating may be exceeded if the input current rating is observed.
The minimum and maximum switch voltage ratings may be exceeded if the switch clamping current rating is observed but may not
exceed 4.6 V.
For TSSOP5 package: above 87.5 C the value of P
For XSON6 package: above 118 C the value of P
To avoid sinking GND current from of terminal Z when switch current flows in terminal Y, the voltage drop across the bidirectional switch
must not exceed 0.4 V. If the switch current flows into terminal Z, no GND current will flow from terminal Y. In this case, there is no limit
for the voltage drop across the switch.
Applies to control signal levels.
supply voltage
input voltage
switch voltage
ambient temperature
input transition rise and fall rate
Limiting values
Recommended operating conditions
Parameter
supply voltage
input voltage
switch voltage
input clamping current
switch clamping current
switch current
storage temperature
total power dissipation
enable input E
V
T
Conditions
V
V
source or sink current
V
pulsed at 1 ms duration, < 10 % duty cycle;
peak current
amb
I
I
SW
SW
All information provided in this document is subject to legal disclaimers.
< 0.5 V
< 0.5 V or V
> 0.5 V or V
> 0.5 V or V
= 40 C to +125 C
Conditions
enable input E
V
CC
Rev. 6 — 21 December 2010
tot
tot
derates linearly with 7.8 mW/K.
= 1.4 V to 4.3 V
derates linearly with 4.0 mW/K.
I
> V
SW
SW
CC
< V
< V
Low-ohmic single-pole single-throw analog switch
+ 0.5 V
CC
CC
+ 0.5 V;
+ 0.5 V;
[1]
[2]
Min
1.4
0
0
40
-
[1]
[2]
[3]
Min
0.5
0.5
0.5
50
-
-
-
65
-
NX3V1T66
Max
4.3
4.3
V
+125
200
© NXP B.V. 2010. All rights reserved.
CC
Max
+4.6
+4.6
V
-
50
500
750
+150
250
CC
+ 0.5 V
Unit
V
V
V
C
ns/V
4 of 20
Unit
V
V
mA
mA
mA
mA
C
mW