SPB106-AP-1 H&D Wireless AB, SPB106-AP-1 Datasheet
SPB106-AP-1
Specifications of SPB106-AP-1
Related parts for SPB106-AP-1
SPB106-AP-1 Summary of contents
Page 1
... SPB106-WiFi 802.11b+g SMD WiFi Board Data Sheet SPB106 WiFi SMD Board ...
Page 2
... All trade names, trademarks and registered trademarks mentioned in this document are property of their respective owners, and are hereby acknowledged. Copyright © 2009 H&D Wireless AB. All rights reserved. Rev. PC3 06/2010 SPB106 WiFi SMD Board Description First issue Updated after review Release after review and updates Info about SDIO interface added ...
Page 3
... Power save .................................................................................................................................................... 12 5.4 Interfaces ...................................................................................................................................................... 12 5.5 RF interface .................................................................................................................................................. 14 5.6 General application information ................................................................................................................ 14 6 PACKAGE SPECIFICATIONS ................................................................................... 17 6.1 Mechanical outline of the SPB106 circuit board ....................................................................................... 17 6.2 Markings on the SPB106 ............................................................................................................................. 17 6.3 Package dimensions ..................................................................................................................................... 18 6.4 Mounting information ................................................................................................................................. 18 7 STANDARDS COMPLIANCE ..................................................................................... 20 Rev. PC3 06/2010 SPB106 WiFi SMD Board ...
Page 4
... Data Sheet - Preliminary 7.1 IEEE/IETF ................................................................................................................................................... 20 7.2 WiFi .............................................................................................................................................................. 20 7.3 Regulatory .................................................................................................................................................... 20 8 SALES OFFICES ........................................................................................................ 23 Rev. PC3 06/2010 SPB106 WiFi SMD Board Data Sheet 1451-SPB106 Confidential page 4 (23) ...
Page 5
... INTRODUCTION 1.1 Overview SPB106 is SMD module with the HDG104 WLAN System In Package, SIP module and all peripheral components required complete solution designed to be surface mount on any host system needing a complete WiFi solution. SPB106 enables a cost efficient ultra low power, high performance and feature rich client solution. ...
Page 6
... Order information . Part No. option SPB106/1 SPB106/3 Ext antenna connector SPB106/e/3 not mounted. Table 2-1: Order information. Rev. PC3 06/2010 SPB106 WiFi SMD Board HDG104 DC/DC for internal power Batch size 10/100 1K/10K/50K 1K/10K/50K Data Sheet 1451-SPB106 Confidential Chip antenna and connector ...
Page 7
... Table 3-2: Recommended operating conditions 3.4 Power Consumption 3.4.1 Current Consumption Mode Conditions All modes All modes All modes All modes All modes 25ºC Tx 25ºC Rev. PC3 06/2010 SPB106 WiFi SMD Board Min 0 -50 Min Typ 2.75 3.3 -20 +25 -30 +25 Parameter Voltage ...
Page 8
... VCC=VPA= 2.75 – 3.6V, DVDD=1.15 - 1.25V External supply, Tamb= -20 – +70°C Parameter Frequency range RF impedance Transmitter performance Output power Output power EVM at +15dBm EVM at +11dBm Rev. PC3 06/2010 SPB106 WiFi SMD Board DVDD 1.2 V VBAT_P+VCC+ VPA+VBAT_32K 3.3 V DVDD 1.2 V VBAT_P+VCC+ VPA+VBAT_32K 3 ...
Page 9
... Table 3-7: SDIO/SPI timing parameter values (high speed mode). Condition: VDDIO= 1.7 – 3.6 V, TA= -20 – +70 Parameter Condition Min Typical Max Units El Figure 3-1: SDIO/SPI timing diagram (default mode) Rev. PC3 06/2010 SPB106 WiFi SMD Board DPSK 1Mbit/s QDPSK 2Mbit/s CCK/DPSK 5.5Mbit/s CCK/BPSKK 11Mbit/s ...
Page 10
... Figure 3-2: SDIO/SPI timing diagram (high speed mode) Parameter Clock fall time Clock rise time Output delay time Output hold time Table 3-7: SDIO/SPI timing parameter values (high speed mode) Rev. PC3 06/2010 SPB106 WiFi SMD Board Symbol Min 5 t ISU 5 t ...
Page 11
... SD_CLK / SPI_CLK 9 GND 10 VCC 11-23 GND 24 DVDD 25 GND 26 GND Table 4-1: Pin assignments Rev. PC3 06/2010 SPB106 WiFi SMD Board Type Description I/O Databit 2 - Not used I/O Databit 1 / Interrupt I Shutdown I/O Databit 3/ SPI Chip Select I/O SDIO_CMD / SPI_MOSI I/O Databit 0 / SPI_MISO ...
Page 12
... Shutdown mode. To end Shutdown mode set SHUTDOWN pin high and reload FW and MIB. 5.3 Power save Power save is a energy saving mode where SPB106 is only listening at regular intervals for the beacons transmitted from an access point and is set in sleep mode in between. During this sleep mode kept in RAM but all not needed functions are turned off ...
Page 13
... PA15 (MCI – CMD [1]) 6 SDIO_CMD PA19 (MCI – DATA8) 7 SDIO_D0 PA27 (MCI – CLK) 8 SD_CLK 9, 11-23, 25,26 GND - 10 VCC - 24 DVDD - Rev. PC3 06/2010 SPB106 WiFi SMD Board SPB105 MISO 7 6 MOSI 8 SCK 5 CS (RESET) 4 (IRQ 3.3V 9 Description Databit 2 Not used ...
Page 14
... PA16 PA15 PA27 GPIO 5.5 RF interface The SPB106 has a high performance chip antenna as the primary RF interface. To enable RF measurements a coaxial connector is available. The connector is switching and compatible with MuRata measurement probe MXHS83QH3000 and similar. 5.6 General application information 5.6.1 Design directions The design using the SPB106 must be performed according to good RF design considerations. All the leads shall be as short as possible between the circuit pins and the external components ...
Page 15
... Data Sheet - Preliminary . 5.6.2 Soldering The SPB106 is a surface mount PCB module. The recommended reflow soldering profile is pictured in Figure 5-2. HDG104 Pin I/O SignalSR Figure 5-2: Reflow Temperature Profile. Rev. PC3 06/2010 SPB106 WiFi SMD Board Figure 5-1: Proposed keep out area ...
Page 16
... Data Sheet - Preliminary Type Rising Zone 125ºC-Peak PSR 1-3 ºC/s Table 5-1: Zone temperatures 5.6.3 Environmental statement The SPB106 is designed and manufactured to comply with the RoHS and Green directives. Rev. PC3 06/2010 SPB106 WiFi SMD Board Preheat Reflow Peak Cooldown Zone ...
Page 17
... Data Sheet - Preliminary 6 PACKAGE SPECIFICATIONS 6.1 Mechanical outline of the SPB106 circuit board 6.2 Markings on the SPB106 The circuit board are marked with a sticker with the units serial number. The FCC id. X02SHDG104 is printed on the top of the PCB. Rev. PC3 06/2010 SPB106 WiFi SMD Board 20 ...
Page 18
... Data Sheet - Preliminary 6.3 Package dimensions 1819 21 20 SPB106 pads (from top) 6.4 Mounting information Recommended land pattern on the PCB Rev. PC3 06/2010 SPB106 WiFi SMD Board A3 Symbol Data Sheet 1451-SPB106 Confidential Text Meas [mm] Module Length 25.80 Module Width 20.60 Pad length 1 ...
Page 19
... Data Sheet - Preliminary Figure 6-2: Land pattern for SPB106 Figure 6-2 shows the recommended land pattern for the SPB106. All measurements referred to the outside corner of the pad outline. Rev. PC3 06/2010 SPB106 WiFi SMD Board Data Sheet 1451-SPB106 Confidential page 19 (23) ...
Page 20
... USA FCC ID XO2HDG104 FCC Canada IC RSS Europe National ETSI Rev. PC3 06/2010 SPB106 WiFi SMD Board Description WLAN MAC& PHY High rate DSSS (5,5/11Mbit/s) Operation in different regulatory domains QoS enhancements Extended rate PHY (ERP-PBCC, DSS-OFDM) Security enhancements Wireless network management Fast BSS transition ...
Page 21
... Any similar wording that expresses the same meaning may be used used with the SPB106 module, the external antennas have been tested and approved which are specified in here below. The SPB106 Module may be integrated with custom design antennas which OEM installer must authorize following the FCC 15 ...
Page 22
... Consult Safety Code 6, obtainable from Health Canada's website www.hc-sc.gc.ca/rpb. 7.3.3 ETSI (Europe) The SPB106 module has been certified for use in European union countries according to ETSI EN 300 328 (Electromagnetic compatibility and Radio spectrum matters for equipment operating in the 2,4 GHz ISM band using spread spectrum modulation techniques). This standard is harmonized within the European Union and covering essential requirements under article 3.2 of the R& ...
Page 23
... SALES OFFICES Global Sales Office Sweden H&D Wireless AB H&D Wireless AB Norgegatan 1 164 32 Kista Sweden E-mail: info@hd-wireless.se Support: support@hd-wireless.se Home page: www.hd-wireless.se Local sales offices and representatives see www.hd-wireless.se Rev. PC3 06/2010 SPB106 WiFi SMD Board Data Sheet 1451-SPB106 Confidential page 23 (23) ...