SPB106-AP-1 H&D Wireless AB, SPB106-AP-1 Datasheet - Page 22

• Manufacturer Part Number: SPB106-AP-1
• Description: WIFI BRD W/RF ANTENNA 802.11B/G
• Manufacturer: H&D Wireless AB
• Type: Transceiver, 802.11 b/gr

Specifications of SPB106-AP-1

• Frequency: 2.4GHz
• Mcu Supported Families: AVR32
• Silicon Manufacturer: H&D Wireless
• Kit Contents: Board
• Features: Low Power Consumption, WEP And AES Hardware Encryption Accelerator Up To 128 Bits
• Core Architecture: Communication & Networking
• Rohs Compliant: Yes
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With/related Products: HDG104
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant, Lead free / RoHS Compliant

Data Sheet - Preliminary
and, if not installed and used in accordance with the instruction manual, may cause harmful
interference to radio communications. Operation of this equipment in a residential area is likely to
cause harmful interference in which case the user will be required to correct the interference at his
own expense (FCC section 15.105
7.3.2 IC (Canada)
Equipment is subject to certification under the applicable RSSs, shall be permanently labeled on
each item, or as an inseparable combination. The label must contain the following information for
full compliance:
IMPORTANT: This equipment for which a certificate has been issued is not considered certified if it
is not properly labeled. The information on the Canadian label can be combined with the
manufacturer's other labeling requirements
IMPORTANT: Operation is subject to the following two conditions: (1) this device may not cause
harmful interference, and (2) this device must accept any interference received, including
interference that may cause undesired operation.
IMPORTANT: To reduce potential radio interference to other users, the antenna type and its gain
should be so chosen that the equivalent isotropically radiated power (e.i.r.p.) is not more than that
permitted for successful communication.
IMPORTANT: The installer of this radio equipment must ensure that the antenna is located or
pointed such that it does not emit RF field in excess of Health Canada limits for the general
population. Consult Safety Code 6, obtainable from Health Canada's website www.hc-sc.gc.ca/rpb.
7.3.3 ETSI (Europe)
The SPB106 module has been certified for use in European union countries according to ETSI EN
300 328 (Electromagnetic compatibility and Radio spectrum matters for equipment operating in the
2,4 GHz ISM band using spread spectrum modulation techniques). This standard is harmonized
within the European Union and covering essential requirements under article 3.2 of the R&TTE-
directive.
If the SPB106 module are incorporated into a product, the manufacturer must ensure compliance
of the final end-user product to the European harmonized EMC and low voltage/safety standards.
A declaration of conformity must be issued for the product including compliance references to
these standards. Underlying the declaration of conformity a technical construction file (TCF),
including all relevant test reports and technical documentation, must be issued and kept on file as
described in Annex II of the R&TTE-directive.
Furthermore, the manufacturer must maintain a copy of the SPB106 module documentation and
ensure the final product does not exceed the specified power ratings, antenna specifications,
and/or installation requirements as specified in the user manual. If any of these specifications are
exceeded in the final product, a complete re-test must be made in order to comply with all relevant
standards as basis for CE-marking. A submission to notified body must be used only if deviations
from standards have been found or if non-harmonized standards have been used.
Certification Number:
Manufacturer’s Name, Trade Name or Brand Name
Model Name:
Rev. PC3 06/2010
).
SPB106 WiFi SMD Board
Confidential
Data Sheet 1451-SPB106
IC: 8713A-HDG104
H&D Wireless AB
HDG104
page 22 (23)