SPB106-AP-1 H&D Wireless AB, SPB106-AP-1 Datasheet - Page 21

• Manufacturer Part Number: SPB106-AP-1
• Description: WIFI BRD W/RF ANTENNA 802.11B/G
• Manufacturer: H&D Wireless AB
• Type: Transceiver, 802.11 b/gr

Specifications of SPB106-AP-1

• Frequency: 2.4GHz
• Mcu Supported Families: AVR32
• Silicon Manufacturer: H&D Wireless
• Kit Contents: Board
• Features: Low Power Consumption, WEP And AES Hardware Encryption Accelerator Up To 128 Bits
• Core Architecture: Communication & Networking
• Rohs Compliant: Yes
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With/related Products: HDG104
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant, Lead free / RoHS Compliant

Data Sheet - Preliminary
Table 7-3: Regulatory Standards
7.3.1 FCC (United States of America)
This equipment complies with Part 15 of the FCC rules and regulations.
To fulfill FCC Certification requirements, an OEM manufacturer must comply with the following
regulations:
1. The modular transmitter must be labeled with its own FCC ID number, and, if the FCC ID is not
visible when the module is installed inside another device, then the outside of the device into which
the module is installed must also display a label referring to the enclosed module. This exterior
label can use wording such as the following:
Example of label required for OEM product containing SPB106 module
Any similar wording that expresses the same meaning may be used.
2. To be used with the SPB106 module, the external antennas have been tested and approved
which are specified in here below. The SPB106 Module may be integrated with custom design
antennas which OEM installer must authorize following the FCC 15.21 requirements.
WARNING: The Original Equipment Manufacturer (OEM) must ensure that the OEM modular
transmitter must be labeled with its own FCC ID number. This includes a clearly visible label on the
outside of the final product enclosure that displays the contents shown below. If the FCC ID is not
visible when the equipment is installed inside another device, then the outside of the device into
which the equipment is installed must also display a label referring to the enclosed equipment.
IMPORTANT: This equipment complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) this device may not cause harmful interference, and (2) this device
must accept any interference received, including interference that may cause undesired operation
(FCC 15.19).
The internal / external antenna(s) used for this mobile transmitter must provide a separation
distance of at least 20 cm from all persons and must not be co-located or operating in conjunction
with any other antenna or transmitter.
Installers must be provided with antenna installation instructions and transmitter operating
conditions for satisfying RF exposure compliance. This device is approved as a mobile device with
respect to RF exposure compliance, and may only be marketed to OEM installers. Use in portable
exposure conditions (FCC 2.1093) requires separate equipment authorization.
IMPORTANT: Modifications not expressly approved by this company could void the user's
authority to operate this equipment (FCC section 15.21).
IMPORTANT: This equipment has been tested and found to comply with the limits for a Class A
digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference when the equipment is operated in a
commercial environment. This equipment generates, uses, and can radiate radio frequency energy
Contains FCC ID: XO2HDG104
The enclosed device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions: (i) this device may not cause harmful interference and (ii) this device must accept any
interference received, including interference that may cause undesired operation.
Rev. PC3 06/2010
SPB106 WiFi SMD Board
Confidential
Data Sheet 1451-SPB106
page 21 (23)