SC16C754BIB80 NXP Semiconductors, SC16C754BIB80 Datasheet - Page 26

• Manufacturer Part Number: SC16C754BIB80
• Description: IC, UART, QUAD, 64BYTE FIFO, 16C754
• Manufacturer: NXP Semiconductors

Specifications of SC16C754BIB80

• No. Of Channels: 4
• Data Rate: 5Mbps
• Supply Voltage Range: 2.25V To 5.5V
• Operating Temperature Range: -40°C To +85°C
• Digital Ic Case Style: LQFP
• No. Of Pins: 80
• Svhc: No SVHC (18-Jun-2010)
• Uart Features: DMA Signalling Capability, Software Selectable Baud Rate Generator
• Rohs Compliant: Yes
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

NXP Semiconductors
SC16C754B_4
Product data sheet
7.5 Line Status Register (LSR)
Table 13
Table 13.
When the LSR is read, LSR[4:2] reflect the error bits (BI, FE, PE) of the character at the
top of the RX FIFO (next character to be read). The LSR[4:2] registers do not physically
exist, as the data read from the RX FIFO is output directly onto the output data bus,
DI[4:2], when the LSR is read. Therefore, errors in a character are identified by reading
the LSR and then reading the RHR.
LSR[7] is set when there is an error anywhere in the RX FIFO, and is cleared only when
there are no more errors remaining in the FIFO.
Reading the LSR does not cause an increment of the RX FIFO read pointer. The RX FIFO
read pointer is incremented by reading the RHR.
Bit
7
6
5
4
3
2
1
0
Symbol
LSR[7]
LSR[6]
LSR[5]
LSR[4]
LSR[3]
LSR[2]
LSR[1]
LSR[0]
shows the line status register bit settings.
Line status register bits description
5 V, 3.3 V and 2.5 V quad UART, 5 Mbit/s (max.) with 64-byte FIFOs
Description
FIFO data error.
THR and TSR empty. This bit is the Transmit Empty indicator.
THR empty. This bit is the Transmit Holding Register Empty indicator.
Break interrupt.
Framing error.
Parity error.
Overrun error.
Data in receiver.
logic 0 = no error (normal default condition)
logic 1 = at least one parity error, framing error, or break indication is in the
receiver FIFO. This bit is cleared when no more errors are present in the
FIFO.
logic 0 = transmitter hold and shift registers are not empty
logic 1 = transmitter hold and shift registers are empty
logic 0 = Transmit Hold Register is not empty
logic 1 = Transmit Hold Register is empty. The processor can now load up
to 64 bytes of data into the THR if the TX FIFO is enabled.
logic 0 = no break condition (normal default condition)
logic 1 = a break condition occurred and associated byte is 00, that is,
RX was LOW for one character time frame
logic 0 = no framing error in data being read from RX FIFO (normal default
condition)
logic 1 = framing error occurred in data being read from RX FIFO, that is,
received data did not have a valid stop bit
logic 0 = no parity error (normal default condition)
logic 1 = parity error in data being read from RX FIFO
logic 0 = no overrun error (normal default condition)
logic 1 = overrun error has occurred
logic 0 = no data in receive FIFO (normal default condition)
logic 1 = at least one character in the RX FIFO
Rev. 04 — 6 October 2008
SC16C754B
© NXP B.V. 2008. All rights reserved.
26 of 51