ST62T08CB6 STMicroelectronics, ST62T08CB6 Datasheet - Page 15

• Manufacturer Part Number: ST62T08CB6
• Description: IC, 8BIT MCU OTP 1K, 62T08, DIP20
• Manufacturer: STMicroelectronics

Specifications of ST62T08CB6

• Controller Family/series: ST6
• Core Size: 8bit
• No. Of I/o's: 12
• Program Memory Size: 1KB
• Ram Memory Size: 64Byte
• Cpu Speed: 8MHz
• Oscillator Type: External Only
• No. Of Timers: 1
• Digital Ic Case: RoHS Compliant
• Peripherals: ADC, LVD
• Rohs Compliant: Yes
• Processor Series: ST62T0x
• Core: ST6
• Data Bus Width: 8 bit
• Program Memory Type: EPROM
• Data Ram Size: 64 B
• Maximum Clock Frequency: 8 MHz
• Number Of Programmable I/os: 12
• Number Of Timers: 2
• Operating Supply Voltage: 3 V to 6 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: Through Hole
• Package / Case: PDIP-20
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 8 bit
• Lead Free Status / Rohs Status: Details

3.2 PROGRAMMING MODES
3.2.1 Program Memory
EPROM/OTP programming mode is set by a
+12.5V voltage applied to the TEST/V
programming flow of the ST62T08C,T09C,T10C,
T20C and E20C is described in the User Manual of
the EPROM Programming Board.
Table 3. ST6208C/09C Program Memory Map
Table 4. ST6210C Program Memory Map
Table 5. ST6220C Program Memory Map
Note: OTP/EPROM devices can be programmed
with the
Device Address
Device Address
Device Address
0FFCh-0FFDh
0FFCh-0FFDh
0FFCh-0FFDh
0BA0h-0F9Fh
0FA0h-0FEFh
0FF8h-0FFBh
0FFEh-0FFFh
0FA0h-0FEFh
0FF8h-0FFBh
0FFEh-0FFFh
0FA0h-0FEFh
0FF8h-0FFBh
0FFEh-0FFFh
0FF0h-0FF7h
0FF0h-0FF7h
0FF0h-0FF7h
0000h-0B9Fh
0880h-0F9Fh
0080h-0F9Fh
0000h-087Fh
0000h-007Fh
development tools available from
NMI Interrupt Vector
NMI Interrupt Vector
NMI Interrupt Vector
Interrupt Vectors
Interrupt Vectors
Interrupt Vectors
Reset Vector
Reset Vector
Reset Vector
Description
Description
Description
User ROM
User ROM
User ROM
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
PP
pin. The
STMicroelectronics (please refer to
page
3.2.2 EPROM Erasing
The EPROM devices can be erased by exposure
to Ultra Violet light. The characteristics of the MCU
are such that erasure begins when the memory is
exposed to light with a wave lengths shorter than
approximately 4000Å. It should be noted that sun-
light and some types of fluorescent lamps have
wavelengths in the range 3000-4000Å.
It is thus recommended that the window of the
MCU packages be covered by an opaque label to
prevent unintentional erasure problems when test-
ing the application in such an environment.
The recommended erasure procedure is exposure
to short wave ultraviolet light which have a wave-
length 2537Å. The integrated dose (i.e. U.V. inten-
sity x exposure time) for erasure should be a mini-
mum of 30W-sec/cm
dosage is approximately 30 to 40 minutes using an
ultraviolet lamp with 12000µW/cm
The EPROM device should be placed within
2.5cm (1inch) of the lamp tubes during erasure.
ST6208C/ST6209C/ST6210C/ST6220C
99).
2
. The erasure time with this
2
Section 12 on
power rating.
15/104
1