DSPIC30F5011-20E/PT Microchip Technology, DSPIC30F5011-20E/PT Datasheet - Page 19

• Manufacturer Part Number: DSPIC30F5011-20E/PT
• Description: IC,DSP,16-BIT,CMOS,TQFP,64PIN,PLASTIC
• Manufacturer: Microchip Technology
• Series: dsPIC™ 30Fr

Specifications of DSPIC30F5011-20E/PT

• Rohs Compliant: YES
• Core Processor: dsPIC
• Core Size: 16-Bit
• Speed: 20 MIPS
• Connectivity: CAN, I²C, SPI, UART/USART
• Peripherals: AC'97, Brown-out Detect/Reset, I²S, LVD, POR, PWM, WDT
• Number Of I /o: 52
• Program Memory Size: 66KB (22K x 24)
• Program Memory Type: FLASH
• Eeprom Size: 1K x 8
• Ram Size: 4K x 8
• Voltage - Supply (vcc/vdd): 2.5 V ~ 5.5 V
• Data Converters: A/D 16x12b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 125°C
• Package / Case: 64-TFQFP
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: XLT64PT5 - SOCKET TRAN ICE 64MQFP/TQFPAC30F008 - MODULE SKT FOR DSPIC30F 64TQFP
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Other names: DSPIC30F5011-20E/PTG; DSPIC30F501120EPT; DSPIC30F501120EPT

23. Module: I
24. Module: I
© 2010 Microchip Technology Inc.
In 10-bit Addressing mode, some address
matches do not set the RBF flag or load the
receive register I2CxRCV, if the lower address
byte
particular, these include all addresses with the
form XX0000XXXX and XX1111XXXX, with the
following exceptions:
• 001111000X
• 011111001X
• 101111010X
• 111111011X
Work around
Ensure that the lower address byte in 10-bit
Addressing mode does not match any 7-bit
reserved addresses.
Affected Silicon Revisions
When the I
slave with and address of 0x102, the I2CxRCV
register content for the lower address byte is 0x01
rather
acknowledges both address bytes.
Work around
None.
Affected Silicon Revisions
A1
A1
X
X
matches
A2
A2
X
X
than
2
2
2
C
C
C module is configured as a 10-bit
A3
A3
X
X
0x02;
the
A4
A4
X
X
reserved
however,
addresses.
the
module
In
25. Module: I
Note:
dsPIC30F5011/5013
When the I
I2CEN bit in the I2CCON register, the dsPIC DSC
device generates a glitch on the SDA and SCL
pins. This glitch falsely indicates “Communication
Start” to all devices on the I
a bus collision in a multi-master configuration.
Additionally, when the I2CEN bit is set, the S and
P bits of the I
‘0’, respectively, which indicate a “Communication
Start” condition.
Work arounds
To avoid this issue, either of the following two work
arounds can be implemented, depending on the
application requirements.
Work around 1:
In a single-master environment, add a delay
between enabling the I
transmission. The delay should be equal to or
greater than the time it takes to transmit two data
bits.
In the multi-master configuration, in addition to the
delay,
synchronized and wait for the I
initialized
communication.
Work around 2:
In dsPIC DSC devices in which the I
multiplexed
precedence in the use of the pin, it is possible to
avoid this glitch by enabling the higher priority
module before enabling the I
Use the following procedure to implement this
work around:
1. Enable the higher priority peripheral module
2. Set up and enable the I
Disable the higher priority peripheral module that
was enabled in step 1.
Affected Silicon Revisions
A1
X
that is multiplexed on the same pins as the I
module.
Work around 2 works only for devices that
share the SDA and SCL pins with another
peripheral that has a higher precedence
over the port latch, such as the UART. The
priority is shown in the pin diagram
located in the data sheet. For example, if
the SDA and SCL pins are shared with the
UART and SPI pins, and the UART has
higher precedence on the port latch pin.
A2
all
X
2
2
before
C
C module is enabled by setting the
other
2
with
A3
C module are set to values ‘1’ and
X
other
A4
X
I
2
initiating
2
C
C module and the first data
2
2
masters
modules
C bus, and can cause
C module.
2
C module.
DS80453E-page 19
2
C module to be
any
2
C module is
should
that
kind
have
2
be
of
C