CV500BC101 Omron, CV500BC101 Datasheet - Page 232
CV500BC101
Manufacturer Part Number
CV500BC101
Description
Programmable Logic Controller
Manufacturer
Omron
Datasheet
1.CV500BC031.pdf
(403 pages)
Specifications of CV500BC101
Peak Reflow Compatible (260 C)
No
Leaded Process Compatible
No
Lead Free Status / RoHS Status
Contains lead / RoHS non-compliant
- Current page: 232 of 403
- Download datasheet (5Mb)
Commands and Responses for Controller Link Units
1: Error log exists
1: Controller transmitter error
1: Data link error stop
Note With CS/CJ-series Optical Controller Link Units, this bit will be 1, even if the
Bit
Status 2 (response): For C200HX/HG/HE, CVM1, and CV-series Controller
Link Units, always set to 00 (Hex). For CS/CJ-series and CQM1H-series
PLCs, the Unit’s setting status is returning in the following configuration.
Status 3 (response): Error information. The configuration is as follows:
Unit is mistakenly connected to an Optical SYSMAC LINK Network.
Status 5 (response): Error information related to the Unit and the PLC. The
configuration is as follows:
A network parameter error, data link table error, or routing table error occurs if
an error is discovered when the parameters and tables are checked at power
up.
A PLC system setting errors occurs if the Controller Link Unit is not properly
recognized by a CS/CJ-series, CVM1, or CV-series PLC.
A PLC model error occurs if a C200HX/HG/HE Controller Link Unit is
mounted to another type of PLC.
Count 1 to Count 8 (response): The total number of times for each of the
items listed below is returned as 1 byte of hexadecimal data.
Count 1: Number of CRC errors
Count 2: Number of token re-sends
Count 3: Number of token returns
Count 4: Number of token timeouts
Count 5: Number of polling timeouts
Count 6: Number of controller changes
Count 7: Number of active node changes
Count 8: Reserved for system use.
For the C200HW-CLK21 and CVM1-CLK21, Count 7: Number of active node
changes is disabled.
For the CS1W-CLK23 and CJ1W-CLK23, Count 5: Number of polling timeouts
is disabled.
7
0
6
1: PLC model error
(C200HX/HG/HE only)
5
Baud rate:
1 Hex: 2 Mbps
2 Hex: 1 Mbps
3 Hex: 500 Kbps
1: PLC system setting error
(CS/CJ-series, CVM1, and CV-series PLCs only)
4
3
Bit
2
1: EEPROM error
1
0
1: Node address setting error
1: Duplicate node address setting error
1: Network parameter error (See note.)
1: Controller hardware error
Bit
For Wired Units:
7
6
0
0
5
4
3
2
0: Terminating resistance OFF
1: Terminating resistance ON
1
0
1: Network parameter error
1: Data link table error
1: Routing table error
Section 6-5
207
Related parts for CV500BC101
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
G6S-2GLow Signal Relay
Manufacturer:
Omron Corporation
Datasheet:
Part Number:
Description:
Compact, Low-cost, SSR Switching 5 to 20 A
Manufacturer:
Omron Corporation
Datasheet:
Part Number:
Description:
Manufacturer:
Omron Corporation
Datasheet:
Part Number:
Description:
Manufacturer:
Omron Corporation
Datasheet:
Part Number:
Description:
Manufacturer:
Omron Corporation
Datasheet:
Part Number:
Description:
Manufacturer:
Omron Corporation
Datasheet:
Part Number:
Description:
Manufacturer:
Omron Corporation
Datasheet:
Part Number:
Description:
Manufacturer:
Omron Corporation
Datasheet: