IAMA3535 Red Lion Controls, IAMA3535 Datasheet - Page 6

• Manufacturer Part Number: IAMA3535
• Description: Isolation Amplifier
• Manufacturer: Red Lion Controls

Specifications of IAMA3535

• Supply Voltage Ac, Min: 0V
• Supply Voltage Dc, Min: 11V
• Width: 3.12"
• Signal Input Type: Selectable Current Or Voltage
• Configuration Setup: DIP Switch
• Iso-amp Mounting Type: DIN Rail
• Supply Voltage Dc, Max: 36V
• Input Accuracy: ± 0.1% Of FS
• Signal Output Type: Selectable Current Or Voltage
• Rohs Compliant: Yes
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

4.0 OUTPUT SCALING USING FIELD CONFIGURATION
GREEN
V
LED
OUT-
I
I
OUT+
RED
LED
OUT-
1V
I
IN
I A M
A
IAMA
10
4
7 8 9
1 2 3
S
T
A
T
U
S
5
12
6
MC2290D
A
S
T
T
U
S
O N
2 0 m
1 0
9
8
7
6
5
4
3
2
1
INPUT
COMM
100V
A /1
~ -
IN
O U
V
IN P
O U
10V
m A
F IE
T F
~ -
U T
T P
L D
O U
IE L
OUT+
U T
R A
/F A
T P
D /F
N G
R A
U T
C T
(AC)
A C
DC+
N G
E
.
(AC)
T .
DC-
E
1
1
1
1
1
2
2
2
2
2
3
3
3
3
3
4
4
4
Step 4.10
4
Step 4.12
4
Step 4.14
Step 4.4
Step 4.5
5
5
S1
S1
5
5
5
S1
S1
S1
6
6
6
6
6
7
7
7
7
7
8
8
8
8
8
9 10
9 10
9 10
9 10
9 10
S2
S2
1
1
S2
S2
S2
1
1
1
ON
ON
ON
ON
ON
4.1 Remove power.
4.2 For voltage output scaling, go to Step 4.4.
4.3 Set 20 mA/1 mA switch (S2) to desired full scale output.
4.4 Set Output Field/Fact. switch (S1 switch 1) to the off position.
4.5 Set Output Range switches (S1 switches 3, 4, and 5) to the desired Output Range
4.6 Connect volt or current meter to appropriate IAMA output terminals.
4.7 An input signal is required to complete output scaling. If previous scaled input is
4.8 Connect input signal source to the correct input terminals based on the maximum
4.9 Apply power to the IAMA and allow a warm up period of five minutes.
4.10 Set Output Field/Fact. switch (S1 switch 1) to the on position.
4.11 Adjust the input signal until the desired * minimum output level is displayed on
4.12 Set Output Field/Fact. switch (S1 switch 1) to the off position.
4.13 Adjust the input signal until the desired * maximum output level is displayed on
4.14 Set Output Field/Fact. switch (S1 switch 1) to the on position.
4.15 Output scaling is complete.
* If the minimum output is higher than the maximum output the module reverses
6
(See Table 2). Select the lowest possible range that will support the desired full
scale output. Example: if the desired span is 1 V to 4 V, the best range selection is
0 to 5 V. (0 to 5 VDC range shown)
used (completed in Step 2.0), Input Field/Fact. switch (S1 switch 2) and Input
Range switches (S1 switches 6 through 10) must remain in the same positions. If
another signal source is used, set Input Field/Fact. switch (S1 switch 2) to off
position and Input Range switches (S1 switches 6 through 10) to the desired input
range (See Table 3).
signal input.
The Red and Green LEDs will alternately blink.
If Red LED blinks slowly, increase signal until Red and Green LEDs alternately
the volt or current meter.
The Red and Green LEDs will alternately blink.
The Red and Green LEDs alternately blink.
If the signal is equal to or below the minimum limit of the selected range, the Red
the volt or current meter.
Red LED extinguishes and Green LED becomes solid. Your scaled values are now
its output behaviour accordingly.
For current output scaling, continue at Step 4.3.
(20 mA - on; 1 mA - off)
Terminal 6: + Voltage
Terminal 5: - Voltage
Terminal 4: + Current
Terminal 1: - Current
Terminal 7: max. signal input 1 VDC
Terminal 8: max. signal input 10 VDC
Terminal 9: max. signal input 100 VDC
Terminal 10: max. signal input 100 mA
Terminal 12: signal common
blink.
LED blinks slowly and the Green LED turns off. Removing power aborts scaling.
Start over at Step 4.1.
saved and will be recalled if the Output Field/Fact. switch (S1 switch 1) is in
the on position when power is applied.