AFCT-57J5APZ Avago Technologies US Inc., AFCT-57J5APZ Datasheet - Page 8

• Manufacturer Part Number: AFCT-57J5APZ
• Description: SM BTS FP SFP Ind-Temp, RoHS
• Manufacturer: Avago Technologies US Inc.

Specifications of AFCT-57J5APZ

• Data Rate: 3.072Gbps
• Wavelength: 1310nm
• Applications: General Purpose
• Voltage - Supply: 2.97 V ~ 3.63 V
• Connector Type: LC Duplex
• Mounting Type: SFP
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

Table 3. Absolute Maximum Ratings
Notes
1. Absolute Maximum Ratings are those values beyond which damage to the device may occur if these limits are exceeded for other than a short
2. Between Absolute Maximum Ratings and the Recommended Operating Conditions functional performance is not intended, device reliability is
3. The module supply voltages, V
Table 4. Recommended Operating Conditions
Notes
1. The Ambient Operating Temperature limitations are based on the Case Operating Temperature limitations and are subject to the host system
2. Recommended Operating Conditions are those values for which functional performance and device reliability is implied.
Table 5. Transceiver Electrical Characteristics
(TC = -40°C to 85°C, VccT, VccR = 3.3V r 10%)
Notes
1. Filter per SFP specification is required on host board to remove 10 Hz to 2 MHz content.
2. Pulled up externally with a 4.7k – 10k: resistor on the host board to 3.3V.
3. Rate_Select, Mod-Def1 and Mod-Def2 must be pulled up externally with a 4.7k – 10k: resistor on the host board to 3.3V.
8
Parameter
Storage Temperature
Case Operating Temperature
Relative Humidity
Supply Voltage
Low Speed Input Voltage
Parameter
Case Operating Temperature
Supply Voltage
Data Rate
Parameter
AC Electrical Characteristics
Power Supply Noise Rejection (peak-
peak)
DC Electrical Characteristics
Module supply current
Power Dissipation
Low Speed Outputs:
Transmit Fault (TX_FAULT),
Loss of Signal (RX_LOS),
MOD-DEF 2
Low Speed Inputs:
Transmit Disable (TX_DIS), Rate Select
(RATE_SELECT)
MOD-DEF 1, MOD-DEF 2
period of time. See Reliability Data Sheet for specific reliability performance.
not implied, and damage to the device may occur over an extended period of time.
thermal design.
CC
T and V
CC
R must not differ by more than 0.5V or damage to the device may occur.
Symbol
T
T
RH
Vcc
V
Symbol
T
Vcc
Symbol
PSNR
I
P
V
V
V
V
CC
S
C
C
IN
DISS
OH
OL
IH
IL
T, R
T, R
Minimum
-40
-40
5
-0.5
-0.5
Minimum
100
2.0
2.0
0
Minimum
-40
2.97
0.614
Maximum
85
3.63
3.072
Maximum
100
100
95
3.8
Vcc+0.5
Maximum
300
350
1000
VccT,R+0.3
0.6
Vcc
0.8
Unit
C
C
%
V
V
Unit
°C
V
Gb/s
Unit
mV
mA
mA
mW
V
V
V
V
Notes
Note 1,2
Note 2
Note 2
Notes
Note 1,2
Note 1,2
Note 1
Note 1,2,3
Note 1
Notes
Note 1
-40°C to 70°C
-40°C to 85°C
Note 2
Note 3