ENW-C9A25C1EF Panasonic - ECG, ENW-C9A25C1EF Datasheet - Page 20

• Manufacturer Part Number: ENW-C9A25C1EF
• Description: RF MODULE 802.15.4 W/PADS NO SW
• Manufacturer: Panasonic - ECG
• Series: PAN4561r

Specifications of ENW-C9A25C1EF

• Frequency: 2.4GHz
• Data Rate - Maximum: 250kbps
• Modulation Or Protocol: 802.15.4
• Applications: General Purpose
• Power - Output: 10dBm
• Sensitivity: -102dBm
• Voltage - Supply: 2.7 V ~ 3.4 V
• Current - Receiving: 47mA
• Current - Transmitting: *
• Data Interface: PCB, Surface Mount
• Memory Size: 60kB Flash, 4kB RAM
• Antenna Connector: PCB, Surface Mount
• Operating Temperature: -40°C ~ 85°C
• Package / Case: Module
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Other names: ENWC9A25C1EF

CLASSIFICATION
SUBJECT
CUSTOMER’S CODE
PAN4561H /M /L
21. RELIABILITY TESTS
22. CAUTIONS
PANASONIC ELECTRONIC DEVICES EUROPE GMBH
The measurement should be done after being exposed to room temperature and humidity for 1
hour.
Die Messungen sollten erst nach einer Stunde Lagerung unter normalen Bedingungen erfolgen.
Failure to do so may result in degrading of the product’s functions and damage to the product.
22.1.
22.2.
No.
1
2
3
4
5
6
(1)
(2)
(3)
(4)
(5)
(6)
(1)
(2)
(3)
Item
Vibration test
Shock test
Heat cycle test
Moisture test
Low temp. test
High temp. test
DESIGN NOTES
INSTALLATION NOTES
Please follow the conditions written in this specification, especially the control
signals of this module.
The supply voltage has to be free of AC ripple voltage (for example from a
battery or a low noise regulator output). For noisy supply voltages, provide a
decoupling circuit (for example a ferrite in series connection and a blocking
capacitor to ground of at least 47uF directly at the module).
This product should not be mechanically stressed when installed.
Heat is the major cause of shortening the life of these products. Please keep this
product away from heat.
Avoid assembly and use of the target equipment in conditions where the
products' temperature may exceed the maximum tolerance.
The supply voltage should not be exceedingly high or reversed. It should not
carry noise and/or spikes.
Please keep this product away from other high frequency circuits.
Reflow soldering is possible twice based on the conditions in chapter 15.
Please set up the temperature at the soldering portion of this product according
to this reflow profile.
Carefully position the products so that their heat will not burn into printed circuit
boards or affect the other components that are susceptible to heat.
Carefully locate these products so that their temperatures will not increase due
to the effects of heat generated by neighboring components.
MODEM FOR 802.15.4 IEEE STANDARD
PRODUCT SPECIFICATION
Limit
Electrical parameter should be
in specification
the same as above
the same as above
the same as above
the same as above
the same as above
PANASONIC PART NUMBER
ENWC9A22xxEF / .25xx. / .21xx.
Condition
a) Freq.:10~50Hz,Amplitude:1.5mm
a) 20min. / cycle,1hrs. each of XYZ axis
b) Freq.:30~100Hz, 6G
b) 20min. / cycle,1hrs. each of XYZ axis
Dropped onto hard wood from height of 50cm for
3 times
-40°C for 30min. and +85°C for 30min.;
each temperature 300 cycles
+60°C, 90% RH, 300h
-40°C, 300h
+85°C, 300h
No.
DS-4561-2400-102
PAGE
DATE
www.pedeu.pansonic.de
06.08.2010
20 of 34
REV.
G