BZ015A104ZAB AVX Corporation, BZ015A104ZAB Datasheet - Page 19

• Manufacturer Part Number: BZ015A104ZAB
• Description: Capacitor,Non-Specified,100mF,5.5VDC,20-% Tol,80+% Tol
• Manufacturer: AVX Corporation
• Series: BZr

Specifications of BZ015A104ZAB

• Capacitance: 0.1 Farad
• Tolerance: - 20 %, 80 %
• Voltage Rating: 5.5 Volts
• Esr: 80 mOhms
• Operating Temperature Range: - 20 C to + 70 C
• Dimensions: 17 mm W x 28 mm L x 2.1 mm H
• Leakage Current: 10 uAmps
• Load Life: 1000 Hrs
• Product: Super Capacitors
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant

BestCap
High Power Pulse Supercapacitors
SECTION 3.4: QUALIFICATION TEST SUMMARY
18
Initial Capacitance
Measurement
Initial DCL
Measurement
Initial ESR
Measurement
Load Life
Shelf Life
Humidity Life
Leg pull strength
Surge Voltage
Temperature Cycling
Temperature
Characteristics
Thermal Shock
Vibration
Test
Step
Step
Step
Step
Step
Charge to test voltage at room temperature. Disconnect parts from
voltage to remove charging effects. Discharge cells with a constant current
(4 mA) noting voltage and time 1 and 2 seconds after beginning discharge.
C = I * dt/dv
Charge to test voltage at room temperature. Disconnect parts from
voltage to remove charging effects. Note voltage and time 5 minutes
and 25 minutes after disconnecting. I = C * dV/dt
Measurement frequency @ 1kHz; Measurement voltage @ 10 mV
at room temperature
Apply test voltage at 70ºC for 1000 hours. Allow to cool to room
temperature and measure Cap, DCL and ESR
Maintain at 70ºC for 1000 hours with no voltage applied. Allow to
cool to room temperature and measure Cap, DCL and ESR.
Maintain at 40°C / 95% RH for 1000 hours. Allow to cool to room
temperature and measure Cap, DCL and ESR.
Apply an increasing force in shear mode until leg pulls away
1
2
3
1
2
3
1
2
3
4
5
6
7
8
1
2
3
1
2
3
4
5
®
Ultra-low ESR
Measure Cap, ESR, DCL (-40ºC rated parts only)
Measure Cap, ESR, DCL
Measure Cap, ESR, DCL
Measure Cap, ESR, DCL
Measure Cap, ESR, DCL
Measure Cap, ESR, DCL
Measure Cap, ESR, DCL
Measure Cap, ESR, DCL
Place cells into an oven at –20°C for 30 minutes
In less than 15 seconds, move cells into a
70ºC oven for 30 minutes
Repeat 1 and 2 for 100 cycles
Apply a harmonic motion that is deflected 0.03 inches
Vary frequency from 10 cycles per second to
55 cycles at a ramp rate of 1 Hz per minute
Vibrate the cells in the X-Y direction for three hours
Vibrate the cells in the Z direction for three hours
Measure Cap, ESR and DCL
Ramp oven down to –20°C and then hold for 15 min.
Ramp oven up to 70ºC and then hold for 15 min.
Apply 125% of the rated voltage for 10 seconds
-40°C
-20°C
-10°C
Temp
25°C
40°C
60°C
70°C
0°C
Repeat 1 and 2 for 1000 cycles
Repeat 1 and 2 for 100 cycles
Short the cell for 10 minutes
Test Method
Soak Time (prior to test)
4 hours
4 hours
4 hours
4 hours
4 hours
4 hours
4 hours
4 hours
Capacitance (Cap)
Leakage Current (DCL)
Equivalent Series
Resistance (ESR)
DCL
Cap
ESR
DCL
Cap
ESR
DCL
Cap
ESR
Yield Force
(A and L leads only)
DCL
Cap
ESR
DCL
Cap
ESR
DCL
70°C
Cap
25°C
ESR
-40°C
-20°C
-10°C
70°C
DCL
Cap
ESR
DCL
Cap
ESR
Parameter
+80% / -20%
of rated Cap
Within Limit
+20% / -50%
< 2.0x rated max.
> 0.7x rated
< 3.0x rated
< 1.5x rated max.
> 0.7x rated
< 2.0x rated
< 1.5x rated max.
> 0.7x rated
< 1.5x rated
Not less than
25 pounds shear
< 1.5x rated max.
> 0.7x rated
< 1.5x rated
< 1.5x rated max.
> 0.7x rated
< 1.5x rated
< 10x rated
> 80% rated
< 20x rated
< 5x rated
< 4x rated
< 1.3x rated
< 1.3x rated
< 2.0x rated max.
> 0.7x rated
< 2.0x rated max.
< 2.0x rated max.
> 0.7x rated
< 2.0x rated max.
of typical value
Limits