HFBR-5963AL Avago Technologies US Inc., HFBR-5963AL Datasheet - Page 3

• Manufacturer Part Number: HFBR-5963AL
• Description: Fiber Optic Transmitters, Receivers, Transceivers OC3/FE 2X5 LC SD LVT TL EXTD TEMP
• Manufacturer: Avago Technologies US Inc.

Specifications of HFBR-5963AL

• Function: Transceivers for ATM, FDDI, Fast Ethernet and SONET OC-3/SDH STM-1 with LC connector.
• Product: Transceiver
• Data Rate: 125 Mbps, 155 Mbps
• Wavelength: 1300 nm
• Maximum Rise Time: 3 ns, 2.2 ns
• Maximum Fall Time: 3 ns, 2.2 ns
• Pulse Width Distortion: 0.4 ns, 0.3 ns
• Maximum Output Current: 50 mA
• Operating Supply Voltage: 2.97 V to 3.63 V
• Maximum Operating Temperature: + 85 C
• Minimum Operating Temperature: - 40 C
• Package / Case: DIP-10 with Connector
• Optical Fiber Type: TX/RX
• Data Transfer Rate: 155.52MBd
• Optical Rise Time: 3/2.2ns
• Optical Fall Time: 3/2.2ns
• Jitter: 0.4/0.3ns
• Operating Temperature Classification: Industrial
• Peak Wavelength: 1308/1380nm
• Package Type: DIP With Connector
• Operating Supply Voltage (min): 2.97V
• Operating Supply Voltage (typ): 3.3V
• Operating Supply Voltage (max): 3.63V
• Output Current: 50mA
• Operating Temp Range: -40C to 85C
• Mounting: Snap Fit To Panel
• Pin Count: 10
• For Use With: Multimode Glass
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

Pin Descriptions:
Pin 1 Receiver Signal Ground V
Directly connect this pin to the receiver ground plane.
Pin 2 Receiver Power Supply Vcc RX
Provide +3.3 V dc via the recommended receiver power
supply filter circuit. Locate the power supply filter circuit
as close as possible to the V
Pin 3 Signal Detect SD
Normal optical input levels to the receiver result in a logic
“1” output.
Low optical input levels to the receiver result in a logic
“0” output.
This Signal Detect output can be used to drive a +3.3 V
TTL input on an upstream circuit, such as Signal Detect
input or Loss of Signal-bar.
Pin 4 Receiver Data Out Bar RD-
No internal terminations are provided. See recommend-
ed circuit schematic.
Pin 5 Receiver Data Out RD+
No internal terminations are provided. See recommend-
ed circuit schematic.
Pin 6 Transmitter Power Supply V
Provide +3.3 V dc via the recommended transmitter
power supply filter circuit.
Locate the power supply filter circuit as close as possible
to the V
Pin 7 Transmitter Signal Ground V
Directly connect this pin to the transmitter ground
plane.
Pin 8 NC
No connection.
Pin 9 Transmitter Data In TD+
No internal terminations are provided. See recommend-
ed circuit schematic.
Pin 10 Transmitter Data In Bar TD-
No internal terminations are provided. See recommend-
ed circuit schematic.

CC
TX pin.
CC
EE
RX pin.
RX
CC
EE
TX
TX
Figure 2. Pin Out Diagram
Mounting Studs/Solder Posts
The mounting studs are provided for transceiver me-
chanical attachment to the circuit board.
It is recommended that the holes in the circuit board be
connected to chassis ground.
Application Information
The Applications Engineering group is available to as-
sist you with the technical understanding and design
trade-offs associated with these transceivers. You can
contact them through your Avago Technologies sales
representative.
The following information is provided to answer some
of the most common questions about the use of these
parts.
Transceiver Optical Power Budget versus Link Length
Optical Power Budget (OPB) is the available optical
power for a fiber optic link to accommodate fiber cable
losses plus losses due to in-line connectors, splices, opti-
cal switches, and to provide margin for link aging and
unplanned losses due to cable plant reconfiguration or
repair.
Avago Technologies LED technology has produced 1300
nm LED devices with lower aging characteristics than
normally associated with these technologies in the indus-
try. The industry convention is 1.5 dB aging for 1300 nm
LEDs. The 1300 nm Avago Technologies LEDs are speci-
fied to experience less than 1 dB of aging over normal
commercial equipment mission life periods.
Contact your Avago Technologies sales representative for
additional details.
RECEIVER SIGNAL GROUND
RECEIVER POWER SUPPLY
RECEIVER DATA OUT BAR
RECEIVER DATA OUT
SIGNAL DETECT
o
o
o
o
o
RX
1
2
3
4
5
View
Top
10
TX
9
8
7
6
o
o
o
o
o
TRANSMITTER DATA IN BAR
TRANSMITTER DATA IN
NC
TRANSMITTER SIGNAL GROUND
TRANSMITTER POWER SUPPLY
Studs/Solder
Mounting
Posts