08055E104MAT2A AVX Corporation, 08055E104MAT2A Datasheet - Page 12

• Manufacturer Part Number: 08055E104MAT2A
• Description: Capacitor, Ceramic; 0.1uF; Chip; Case 0805; +/-20%; 50WVDC; SMD; Z5U; 100000 Mohm; 0.05I
• Manufacturer: AVX Corporation
• Series: 0805r

Specifications of 08055E104MAT2A

• Tolerance (+ Or -): 20%
• Voltage: 50VDC
• Temp Coeff (dielectric): Z5U
• Operating Temp Range: 10C to 85C
• Mounting Style: Surface Mount
• Construction: SMT Chip
• Case Style: Ceramic Chip
• Failure Rate: Not Required
• Wire Form: Not Required
• Product Length (mm): 2.01mm
• Product Depth (mm): 1.25mm
• Product Height (mm): 1.3mm
• Product Diameter (mm): Not Requiredmm
• Capacitance: .1uF
• Package / Case: 0805
• Brand/series: AVX
• Case Code: 0805
• Case Size: 0805
• Dielectric Strength: No breakdown or visual defects
• Insulation Resistance: 100000 Megohms
• Length: 0.079 in. ± 0.008 in.
• Material, Element: Ceramic
• Package Type: 0805
• Temperature, Operating, Maximum: 125 °C
• Temperature, Operating, Minimum: -55 °C
• Termination: SMT
• Tolerance: ±20 %
• Voltage, Rating: 50 VDC
• Width: 0.049 in. ± 0.008 in.
• Voltage Rating: 50 Volts
• Operating Temperature Range: + 10 C to + 85 C
• Temperature Coefficient / Code: Z5U
• Product: General Type MLCCs
• Dimensions: 0.049 in W x 0.079 in L x 0.930 mm H
• Termination Style: SMD/SMT
• Lead Free Status / RoHS Status: Compliant

Embossed Carrier Configuration
8 & 12mm Tape Only
8 & 12mm Embossed Tape
Metric Dimensions Will Govern
CONSTANT DIMENSIONS
VARIABLE DIMENSIONS
NOTES:
1. A
2. Tape with components shall pass around radius “R” without damage. The minimum trailer length (Note 2 Fig. 3) may require additional length to provide R min. for 12 mm
3. G
4. G
5. The embossment hole location shall be measured from the sprocket hole controlling the location of the embossment.
6. B
Tape Size
Tape Size
clearance between the end of the terminals or body of the component to the sides and depth of the cavity (A
(.020) max. The clearance allowed must also prevent rotation of the component within the cavity of not more than 20 degrees (see sketches C & D).
embossed tape for reels with hub diameters approaching N min. (Table 4).
cavity whichever is less.
or to the edge of the cavity whichever is less.
Dimensions of embossment location and hole location shall be applied independent of each other.
1/2 Pitch
0
1
1
2
Double
, B
12mm
12mm
12mm
dimension is a reference dimension for tape feeder clearance only.
dimension is the flat area from the edge of the sprocket hole to either the outward deformation of the carrier tape between the embossed cavities or to the edge of the
dimension is the flat area from the edge of the carrier tape opposite the sprocket holes to either the outward deformation of the carrier tape between the embossed cavity
8mm
8mm
8mm
Pitch
and
0
, and K
0
are determined by the max. dimensions to the ends of the terminals extending from the component body and/or the body dimensions of the component. The
See Note 6 See Note 5
(.059
8.4
(.179)
(.323)
(.179)
(.323)
Max.
4.55
4.55
8.2
8.2
D
B
+0.10
-0.0
0
1
+.004
-0.0
)
(.069 ± .004) (.157 ± .004) (.079 ± .002)
1.75 ± 0.10
(.039)
(.059)
(.039)
(.059)
Min.
1.0
1.5
1.0
1.5
D
E
1
(.138 ± .002) (.157 ± .004)
(.217 ± .002) (.157 ± .004)
(.138 ± .002) 0.79 ± .004
(.217 ± .002) (.315 ± .004)
4.0 ± 0.10
3.5 ± 0.05
5.5 ± 0.05
3.5 ± 0.05
5.5 ± 0.05
P
F
0
4.0 ± 0.10
4.0 ± 0.10
2.0 ± 0.10
8.0 ± 0.10
2.0 ± 0.05
P
P
2
1
See Note 2
T Max.
(1.181)
(1.181)
0.600
(.024)
(.984)
(.984)
Min.
25
30
25
30
R
0
, B
0
, and K
6.5 Max.
2.5 Max.
6.5 Max.
2.5 Max
0
(.004)
(.098)
(.256)
(.098)
(.256)
Max.
) must be within 0.05 mm (.002) min. and 0.50 mm
0.10
T
T
1
2
(.472 ± .012)
(.472 ± .012)
See Note 3
12.0 ± .30
12.0 ± .30
(.315
(.315
(.030)
8.0
0.75
Min.
8.0
G
W
1
+0.3
+0.3
-0.1
-0.1
+.012
+.012
-.004
-.004
)
)
See Note 4
See Note 1
See Note 1
See Note 1
See Note 1
A
(.030)
0
0.75
Min.
G
B
2
0
K
0
33