LFE2-50E-H-EV Lattice, LFE2-50E-H-EV Datasheet - Page 8
![no-image](/images/manufacturer_photos/0/3/380/lattice_sml.jpg)
LFE2-50E-H-EV
Manufacturer Part Number
LFE2-50E-H-EV
Description
MCU, MPU & DSP Development Tools LatticeECP2 Eval Brd - Advanced
Manufacturer
Lattice
Datasheet
1.LFE2-12SE-6FN256C.pdf
(389 pages)
Specifications of LFE2-50E-H-EV
Processor To Be Evaluated
LatticeECP2 FPGA
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
- Current page: 8 of 389
- Download datasheet (5Mb)
Lattice Semiconductor
Modes of Operation
Each slice has up to four potential modes of operation: Logic, Ripple, RAM and ROM.
Logic Mode
In this mode, the LUTs in each slice are configured as 4-input combinatorial lookup tables. A LUT4 can have 16
possible input combinations. Any four input logic functions can be generated by programming this lookup table.
Since there are two LUT4s per slice, a LUT5 can be constructed within one slice. Larger look-up tables such as
LUT6, LUT7 and LUT8 can be constructed by concatenating other slices. Note LUT8 requires more than four
slices.
Ripple Mode
Ripple mode supports the efficient implementation of small arithmetic functions. In ripple mode, the following func-
tions can be implemented by each slice:
• Addition 2-bit
• Subtraction 2-bit
• Add/Subtract 2-bit using dynamic control
• Up counter 2-bit
• Down counter 2-bit
• Up/Down counter with Async clear
• Up/Down counter with preload (sync)
• Ripple mode multiplier building block
• Multiplier support
• Comparator functions of A and B inputs
Ripple Mode includes an optional configuration that performs arithmetic using fast carry chain methods. In this con-
figuration (also referred to as CCU2 mode) two additional signals, Carry Generate and Carry Propagate, are gener-
ated on a per slice basis to allow fast arithmetic functions to be constructed by concatenating Slices.
RAM Mode
In this mode, a 16x4-bit distributed single port RAM (SPR) can be constructed using each LUT block in Slice 0 and
Slice 2 as a 16x1-bit memory. Slice 1 is used to provide memory address and control signals. A 16x2-bit pseudo
dual port RAM (PDPR) memory is created by using one Slice as the read-write port and the other companion slice
as the read-only port.
The Lattice design tools support the creation of a variety of different size memories. Where appropriate, the soft-
ware will construct these using distributed memory primitives that represent the capabilities of the PFU. Table 2-3
shows the number of slices required to implement different distributed RAM primitives. For more information about
using RAM in LatticeECP2/M devices, please see the list of additional technical documentation at the end of this
data sheet.
Table 2-3. Number of Slices Required to Implement Distributed RAM
– A greater-than-or-equal-to B
– A not-equal-to B
– A less-than-or-equal-to B
Number of slices
Note: SPR = Single Port RAM, PDPR = Pseudo Dual Port RAM
SPR 16X4
2-5
3
LatticeECP2/M Family Data Sheet
PDPR 16X4
3
Architecture
Related parts for LFE2-50E-H-EV
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
![LFE2-50E-5FN484C](/images/manufacturer_photos/0/3/381/lattice_semiconductor_tmb.jpg)
Part Number:
Description:
IC, LATTICEECP2 FPGA, 420MHZ, FPBGA-484
Manufacturer:
LATTICE SEMICONDUCTOR
Datasheet:
![LFE2-50E-H-EVN](/images/manufacturer_photos/0/3/380/lattice_tmb.jpg)
Part Number:
Description:
Development Software Evaluation Board
Manufacturer:
Lattice
![LFE2-50E-VID-EV](/images/manufacturer_photos/0/3/380/lattice_tmb.jpg)
Part Number:
Description:
Development Software LatticeECP2 Video Dev Kit
Manufacturer:
Lattice
Datasheet:
![LFE2-50E-D-EVN](/images/manufacturer_photos/0/3/380/lattice_tmb.jpg)
Part Number:
Description:
MCU, MPU & DSP Development Tools LatticeMico32/DSP DEV BD/LatticeECP2
Manufacturer:
Lattice
Datasheet:
![LFE2-50E-L-EV](/images/manufacturer_photos/0/3/380/lattice_tmb.jpg)
Part Number:
Description:
MCU, MPU & DSP Development Tools ECP-2 Standard Eval Board
Manufacturer:
Lattice
Datasheet:
![LFE2-50E-D-EV](/images/manufacturer_photos/0/3/380/lattice_tmb.jpg)
Part Number:
Description:
MCU, MPU & DSP Development Tools LS Mico32/DSP Dev Br Brd for LS ECP2
Manufacturer:
Lattice
Datasheet:
![LFE2-50E-5F672C](/images/manufacturer_photos/0/3/381/lattice_semiconductor_tmb.jpg)
Part Number:
Description:
FPGA LatticeECP2 Family 48000 Cells 90nm (CMOS) Technology 1.2V 672-Pin FBGA
Manufacturer:
LATTICE SEMICONDUCTOR
Datasheet:
![LFE2-50E-5FN484I](/images/manufacturer_photos/0/3/381/lattice_semiconductor_tmb.jpg)
Part Number:
Description:
FPGA LatticeECP2 Family 48000 Cells 90nm (CMOS) Technology 1.2V 484-Pin FBGA
Manufacturer:
LATTICE SEMICONDUCTOR
Datasheet:
![LFE2-50E-5FN672C](/images/manufacturer_photos/0/3/380/lattice_tmb.jpg)
Part Number:
Description:
IC FPGA 50KLUTS 500I/O 672-BGA
Manufacturer:
Lattice
Datasheet:
![LFE2-50E-6F484C](/images/manufacturer_photos/0/3/380/lattice_tmb.jpg)
Part Number:
Description:
IC FPGA 50KLUTS 339I/O 484-BGA
Manufacturer:
Lattice
Datasheet:
![LFE2-50E-6FN484C](/images/manufacturer_photos/0/3/380/lattice_tmb.jpg)
Part Number:
Description:
IC FPGA 50KLUTS 339I/O 484-BGA
Manufacturer:
Lattice
Datasheet:
![LFE2-50E-7FN484C](/images/manufacturer_photos/0/3/380/lattice_tmb.jpg)
Part Number:
Description:
IC FPGA 50KLUTS 339I/O 484-BGA
Manufacturer:
Lattice
Datasheet:
![LFE2-50E-7FN672C](/images/manufacturer_photos/0/3/380/lattice_tmb.jpg)
Part Number:
Description:
IC FPGA 50KLUTS 500I/O 672-BGA
Manufacturer:
Lattice
Datasheet:
![LFE2-50E-5F484I](/images/manufacturer_photos/0/3/380/lattice_tmb.jpg)
Part Number:
Description:
FPGA 48000 CELLS 90NM (CMOS) 1.2
Manufacturer:
Lattice
Datasheet:
![LFE2-50E-6FN672C](/images/manufacturer_photos/0/3/380/lattice_tmb.jpg)
Part Number:
Description:
IC FPGA 48KLUTS 672FPBGA
Manufacturer:
Lattice
Datasheet: