AD7631BCPZ Analog Devices Inc, AD7631BCPZ Datasheet - Page 9

• Manufacturer Part Number: AD7631BCPZ
• Description: IC,A/D CONVERTER,SINGLE,18-BIT,CMOS,LLCC,48PIN
• Manufacturer: Analog Devices Inc
• Series: PulSAR®r

Specifications of AD7631BCPZ

• Number Of Bits: 18
• Sampling Rate (per Second): 250k
• Data Interface: Serial, Parallel
• Number Of Converters: 1
• Power Dissipation (max): 120mW
• Voltage Supply Source: Analog and Digital
• Operating Temperature: -40°C ~ 85°C
• Mounting Type: Surface Mount
• Package / Case: 48-VFQFN, CSP Exposed Pad
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

Pin No.
11, 12
13
14
15
16
18
19
20
21
22
Mnemonic
D[4:5] or
DIVSCLK[0:1]
D6 or
EXT/INT
D7 or
INVSYNC
D8 or
INVSCLK
D9 or
RDC or
SDIN
OVDD
DVDD
DGND
D10 or
SDOUT
D11 or
SDCLK
DI/O
Type
DO/I
DI/O
DI/O
DI/O
P
P
P
DI/O
DI/O
1
Description
When MODE[1:0] = 0, 1, or 2, these pins are Bit 4 and Bit 5 of the parallel port data output bus.
When MODE[1:0] = 3, serial data clock division selection. When using serial master read after convert
mode (EXT/INT = low, RDC/SDIN = low), these inputs can be used to slow down the internally generated
serial clock that clocks the data output. In other serial modes, these pins are high impedance outputs.
When MODE[1:0] = 0, 1, or 2, this output is used as Bit 6 of the parallel port data output bus.
When MODE[1:0] = 3, Serial Data Clock Source Select. In serial mode, this input is used to select the
internally generated (master) or the external (slave) serial data clock for the AD7631 output data.
When EXT/INT = low (master mode), the internal serial data clock is selected on SDCLK output.
When EXT/INT = high (slave mode), the output data is synchronized to an external clock signal (gated by CS)
connected to the SDCLK input.
When MODE[1:0] = 0, 1, or 2, this output is used as Bit 7 of the parallel port data output bus.
When MODE[1:0] = 3, Serial Data Invert Sync Select. In serial master mode (MODE[1:0] = 3,
EXT/INT = low), this input is used to select the active state of the SYNC signal.
When INVSYNC = low, SYNC is active high.
When INVSYNC = high, SYNC is active low.
When MODE[1:0] = 0, 1, or 2, this output is used as Bit 8 of the parallel port data output bus.
When MODE[1:0] = 3, Invert SDCLK/SCCLK Select. This input is used to invert both SDCLK and SCCLK.
When INVSCLK = low, the rising edge of SDCLK/SCCLK are used.
When INVSCLK = high, the falling edge of SDCLK/SCCLK are used.
When MODE[1:0] = 0, 1, or 2, this output is used as Bit 9 of the parallel port data output bus.
When MODE[1:0] = 3, Serial Data Read During Convert. In serial master mode (MODE[1:0] = 3,
EXT/INT = low), RDC is used to select the read mode. See the
When RDC = low, the current result is read after conversion. Note the maximum throughput is
not attainable in this mode.
When RDC = high, the previous conversion result is read during the current conversion.
When MODE[1:0] = 3, Serial Data In. In serial slave mode (MODE[1:0] = 3, EXT/INT = high), SDIN can
be used as a data input to daisy-chain the conversion results from two or more ADCs onto a single
SDOUT line. The digital data level on SDIN is output on SDOUT with a delay of 16 SDCLK periods after
the initiation of the read sequence.
Input/Output Interface Digital Power. Nominally at the same supply as the supply of the host
interface 2.5 V, 3 V, or 5 V and decoupled with 10 μF and 100 nF capacitors.
Digital Power. Nominally at 4.75 V to 5.25 V and decoupled with 10 μF and 100 nF capacitors. Can
be supplied from AVDD.
Digital Power Ground. Ground reference point for digital outputs. Should be connected to system
digital ground ideally at the same potential as AGND and OGND.
When MODE[1:0] = 0, 1, or 2, this output is used as Bit 10 of the parallel port data output bus.
synchronized to SDCLK. Conversion results are stored in an on-chip register. The AD7631 provides
the conversion result, MSB first, from its internal shift register. The data format is determined by
the logic level of OB/2C.
When EXT/INT = low (master mode), SDOUT is valid on both edges of SDCLK.
When EXT/INT = high (slave mode):
When MODE[1:0] = 0, 1, or 2, this output is used as Bit 11 of the parallel port data output bus.
When MODE[1:0] = 3, Serial Data Clock. In all serial modes, this pin is used as the serial data clock
input or output, dependent on the logic state of the EXT/INT pin. The active edge where the data
SDOUT is updated depends on the logic state of the INVSCLK pin.
When MODE[1:0] = 3, Serial Data Output. In all serial modes, this pin is used as the serial data output
When INVSCLK = low, SDOUT is updated on SDCLK rising edge.
When INVSCLK = high, SDOUT is updated on SDCLK falling edge.
Rev. A | Page 9 of 32
Master Serial Interface
section.
AD7631