AD7983BCPZ-RL Analog Devices Inc, AD7983BCPZ-RL Datasheet - Page 12

• Manufacturer Part Number: AD7983BCPZ-RL
• Description: IC,A/D CONVERTER,SINGLE,16-BIT,LLCC,10PIN
• Manufacturer: Analog Devices Inc
• Series: PulSAR®r

Specifications of AD7983BCPZ-RL

• Number Of Bits: 16
• Sampling Rate (per Second): 1.33M
• Data Interface: DSP, MICROWIRE™, QSPI™, Serial, SPI™
• Number Of Converters: 1
• Power Dissipation (max): 12mW
• Voltage Supply Source: Single Supply
• Operating Temperature: -40°C ~ 85°C
• Mounting Type: Surface Mount
• Package / Case: 10-WFDFN, CSP Exposed Pad
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

AD7983
THEORY OF OPERATION
CIRCUIT INFORMATION
The AD7983 is a fast, low power, single-supply, precise 16-bit
ADC that uses a successive approximation architecture.
The AD7983 is capable of converting 1,000,000 samples per
second (1 MSPS) and powers down between conversions. When
operating at 10 kSPS, for example, it consumes 70 μW typically,
making it ideal for battery-powered applications.
The AD7983 provides the user with an on-chip track-and-hold
and does not exhibit any pipeline delay or latency, making it
ideal for multiple multiplexed channel applications.
The AD7983 can be interfaced to any 1.8 V to 5 V digital logic
family. It is available in a 10-lead MSOP or a tiny 10-lead QFN
(LFCSP) that allows space savings and flexible configurations.
It is pin-for-pin compatible with the 18-bit AD7982.
CONVERTER OPERATION
The AD7983 is a successive approximation ADC based on a
charge redistribution DAC. Figure 21 shows the simplified
schematic of the ADC. The capacitive DAC consists of two
identical arrays of 16 binary weighted capacitors, which are
connected to the two comparator inputs.
GND
REF
IN+
IN–
32,768C
32,768C
16,384C
16,384C
MSB
MSB
4C
4C
Figure 21. ADC Simplified Schematic
2C
2C
Rev. A | Page 12 of 24
C
C
During the acquisition phase, terminals of the array tied to the
input of the comparator are connected to GND via SW+ and
SW−. All independent switches are connected to the analog
inputs. Therefore, the capacitor arrays are used as sampling
capacitors and acquire the analog signal on the IN+ and IN−
inputs. When the acquisition phase is complete and the CNV
input goes high, a conversion phase is initiated. When the
conversion phase begins, SW+ and SW− are opened first. The two
capacitor arrays are then disconnected from the inputs and
connected to the GND input. Therefore, the differential voltage
between the inputs IN+ and IN− captured at the end of the
acquisition phase is applied to the comparator inputs, causing
the comparator to become unbalanced. By switching each
element of the capacitor array between GND and REF, the
comparator input varies by binary weighted voltage steps
(V
switches, starting with the MSB, to bring the comparator back
into a balanced condition. After the completion of this process,
the part returns to the acquisition phase and the control logic
generates the ADC output code and a busy signal indicator.
Because the AD7983 has an on-board conversion clock, the
serial clock, SCK, is not required for the conversion process.
C
C
REF
/2, V
LSB
LSB
REF
SW+
SW+
/4 … V
SWITCHES CONTROL
COMP
REF
/65,536). The control logic toggles these
CONTROL
LOGIC
CNV
BUSY
OUTPUT CODE