AD9516-2BCPZ-REEL7 Analog Devices Inc, AD9516-2BCPZ-REEL7 Datasheet - Page 35

• Manufacturer Part Number: AD9516-2BCPZ-REEL7
• Description: IC,Ten Distributed-Output Clock Driver,LLCC,64PIN,PLASTIC
• Manufacturer: Analog Devices Inc
• Type: Clock Generator, Fanout Distributionr

Specifications of AD9516-2BCPZ-REEL7

• Pll: Yes
• Input: Clock
• Output: CMOS, LVDS, LVPECL
• Number Of Circuits: 1
• Ratio - Input:output: 1:14
• Differential - Input:output: Yes/Yes
• Frequency - Max: 2.33GHz
• Divider/multiplier: Yes/No
• Voltage - Supply: 3.135 V ~ 3.465 V
• Operating Temperature: -40°C ~ 85°C
• Mounting Type: Surface Mount
• Package / Case: 64-LFCSP
• Frequency-max: 2.33GHz
• Function: Clock Generator
• Operating Temperature (max): 85C
• Operating Temperature (min): -40C
• Package Type: LFCSP EP
• Pin Count: 64
• Mounting: Surface Mount
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: AD9516-2/PCBZ - BOARD EVAL FOR AD9516-2 2.2GHZ
• Lead Free Status / Rohs Status: Compliant

By using combinations of DM and FD modes, the AD9516 can
achieve values of N all the way down to N = 1 and up to N =
26,2175. Table 28 shows how a 10 MHz reference input can be
locked to any integer multiple of N.
Note that the same value of N can be derived in different ways,
as illustrated by the case of N = 12. The user can choose a fixed
divide mode of P = 2 with B = 6; use the dual modulus mode of
2/3 with A = 0, B = 6; or use the dual modulus mode of 4/5 with
A = 0, B = 3.
The maximum frequency into the prescaler in 2/3 dual-modulus
mode is limited to 200 MHz. There are only two cases where
this frequency limitation limits the flexibility of that N divider:
N = 7 and N = 11. In these two cases, the maximum frequency
into the prescaler is 300 MHz and is achieved by using the P = 1
FD mode. In all other cases, the user can achieve the desired N
divider value by using the other prescaler modes.
A and B Counters
The B counter must be ≥3 or bypassed, and, unlike the R counter,
A = 0 is actually zero.
When the prescaler is in dual modulus mode, the A counter
must be less than the B counter.
The maximum input frequency to the A/B counter is reflected
in the maximum prescaler output frequency (~300 MHz) that is
specified in Table 2. This is the prescaler input frequency (VCO or
Table 28. Using a 10 MHz Reference Input to Generate Different VCO Frequencies
f
(MHz)
10
10
10
10
10
10
10
10
10
10
10
10
10
10
10
10
10
REF
R
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
P
1
2
1
1
1
2
2
2
2
2
2
2
2
2
2
4
4
A
X
X
X
X
X
X
0
1
2
1
X
0
1
X
0
0
1
B
1
1
3
4
5
3
3
3
3
4
5
5
5
6
6
3
3
N
1
2
3
4
5
6
6
7
8
9
10
10
11
12
12
12
13
f
(MHz)
10
20
30
40
50
60
60
70
80
90
100
100
110
120
120
120
130
VCO
Mode
FD
FD
FD
FD
FD
FD
DM
DM
DM
DM
FD
DM
DM
FD
DM
DM
DM
Rev. A | Page 35 of 80
Comments/Conditions
P = 1, B = 1 (A and B counters are bypassed).
P = 2, B = 1 (A and B counters are bypassed).
A counter is bypassed.
A counter is bypassed.
A counter is bypassed.
A counter is bypassed.
Maximum frequency into prescaler in P = 2/3 mode is 200 MHz.
If N = 7 or N = 11 is desired for prescaler input frequency of 200 MHz
to 300 MHz, use P = 1, and N = 7 or 11, respectively.
P = 8 is not allowed (2700 ÷ 8 > 300 MHz).
P = 32 is not allowed (A > B not allowed).
P = 32, A = 22, B = 84.
P = 16 is also permitted.
CLK) divided by P. For example, a dual modulus mode of P = 8/9
is not allowed if the VCO frequency is greater than 2400 MHz
because the frequency going to the A/B counter is too high.
When the AD9516 B counter is bypassed (B = 1), the A counter
should be set to 0, and the overall resulting divide is equal to the
prescaler setting, P. The possible divide ratios in this mode are
1, 2, 3, 4, 8, 16, and 32. This mode is useful only when an
external VCO/VCXO is used because the frequency range of the
internal VCO requires an overall feedback divider greater than 32.
Although manual reset is not normally required, the A/B counters
have their own reset bit. Alternatively, the A and B counters can be
reset using the shared reset bit of the R, A, and B counters. Note
that these reset bits are not self-clearing.
R, A, and B Counters— SYNC Pin Reset
The R, A and B counters can also be reset simultaneously through
the SYNC pin. This function is controlled by Register 0x019[7:6]
(see Table 54). The SYNC pin reset is disabled by default.
R and N Divider Delays
Both the R and N dividers feature a programmable delay cell.
These delays can be enabled to allow adjustment of the phase
relationship between the PLL reference clock and the VCO or
CLK. Each delay is controlled by three bits. The total delay
range is about 1 ns. See Register 0x019 in Table 54.
AD9516-2