AD9518-1BCPZ-REEL7 Analog Devices Inc, AD9518-1BCPZ-REEL7 Datasheet - Page 60
![IC,Six Distributed-Output Clock Driver,LLCC,48PIN,PLASTIC](/photos/6/50/65022/cp-48-8_sml.jpg)
AD9518-1BCPZ-REEL7
Manufacturer Part Number
AD9518-1BCPZ-REEL7
Description
IC,Six Distributed-Output Clock Driver,LLCC,48PIN,PLASTIC
Manufacturer
Analog Devices Inc
Type
Clock Generator, Fanout Distributionr
Datasheet
1.AD9518-1ABCPZ-RL7.pdf
(64 pages)
Specifications of AD9518-1BCPZ-REEL7
Pll
Yes
Input
CMOS, LVDS, LVPECL
Output
LVPECL
Number Of Circuits
1
Ratio - Input:output
1:6
Differential - Input:output
Yes/Yes
Frequency - Max
2.65GHz
Divider/multiplier
Yes/No
Voltage - Supply
3.135 V ~ 3.465 V
Operating Temperature
-40°C ~ 85°C
Mounting Type
Surface Mount
Package / Case
48-LFCSP
Frequency-max
2.65GHz
Function
Clock Generator
Operating Temperature (max)
85C
Operating Temperature (min)
-40C
Package Type
LFCSP EP
Pin Count
48
Mounting
Surface Mount
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
For Use With
AD9518-1/PCBZ - BOARD EVAL FOR AD9518-1
Lead Free Status / Rohs Status
Compliant
AD9518-1
APPLICATIONS INFORMATION
FREQUENCY PLANNING USING THE AD9518
The AD9518 is a highly flexible PLL. When choosing the PLL
settings and version of the AD9518, keep in mind the following
guidelines.
The AD9518 has the following four frequency dividers: the
reference (or R) divider, the feedback (or N) divider, the VCO
divider, and the channel divider. When trying to achieve a
particularly difficult frequency divide ratio requiring a large
amount of frequency division, some of the frequency division
can be done by either the VCO divider or the channel divider,
thus allowing a higher phase detector frequency and more
flexibility in choosing the loop bandwidth.
Within the AD9518 family, lower VCO frequencies generally
result in slightly lower jitter. The difference in integrated jitter
(from 12 kHz to 20 MHz offset) for the same output frequency is
usually less than 150 fs over the entire VCO frequency range
(1.45 GHz to 2.95 GHz) of the AD9518 family. If the desired
frequency plan can be achieved with a version of the AD9518
that has a lower VCO frequency, choosing the lower frequency
part results in the lowest phase noise and the lowest jitter.
However, choosing a higher VCO frequency may result in more
flexibility in frequency planning.
Choosing a nominal charge pump current in the middle of the
allowable range as a starting point allows the designer to increase or
decrease the charge pump current, and thus allows the designer
to fine-tune the PLL loop bandwidth in either direction.
ADIsimCLK is a powerful PLL modeling tool that can be
downloaded from www.analog.com. It is very accurate in
determining the optimal loop filter for a given application.
USING THE AD9518 OUTPUTS FOR ADC CLOCK
APPLICATIONS
Any high speed ADC is extremely sensitive to the quality of its
sampling clock. An ADC can be thought of as a sampling mixer,
and any noise, distortion, or timing jitter on the clock is combined
with the desired signal at the analog-to-digital output. Clock
integrity requirements scale with the analog input frequency
and resolution, with higher analog input frequency applications
at ≥14-bit resolution being the most stringent. The theoretical
SNR of an ADC is limited by the ADC resolution and the jitter
on the sampling clock.
Rev. A | Page 60 of 64
Considering an ideal ADC of infinite resolution where the step
size and quantization error can be ignored, the available SNR
can be expressed approximately by
where:
f
t
Figure 51 shows the required sampling clock jitter as a function
of the analog frequency and effective number of bits (ENOB).
For more information, see the AN-756 Application Note, Sampled
Systems and the Effects of Clock Phase Noise and Jitter; and the
AN-501 Application Note, Aperture Uncertainty and ADC System
Performance, at www.analog.com.
Many high performance ADCs feature differential clock inputs
to simplify the task of providing the required low jitter clock on
a noisy PCB. (Distributing a single-ended clock on a noisy PCB
may result in coupled noise on the sample clock. Differential
distribution has inherent common-mode rejection that can provide
superior clock performance in a noisy environment.) The AD9518
features LVPECL outputs that provide differential clock outputs,
which enable clock solutions that maximize converter SNR
performance. The input requirements of the ADC (differential
or single-ended, logic level, termination) should be considered
when selecting the best clocking/ converter solution.
A
J
is the rms jitter on the sampling clock.
is the highest analog frequency being digitized.
110
100
90
80
70
60
50
40
30
SNR
10
(
Figure 51. SNR and ENOB vs. Analog Input Frequency
dB
)
=
20
×
log
⎛
⎜
⎜
⎝
2
π
1
f
f
A
A
t
100
(MHz)
J
⎞
⎟
⎟
⎠
SNR = 20log
2πf
1
A
t
J
1k
18
16
14
12
10
8
6