AD9627BCPZ-150 Analog Devices Inc, AD9627BCPZ-150 Datasheet - Page 29

• Manufacturer Part Number: AD9627BCPZ-150
• Description: IC,A/D CONVERTER,DUAL,12-BIT,LLCC,64PIN
• Manufacturer: Analog Devices Inc

Specifications of AD9627BCPZ-150

• Number Of Bits: 12
• Sampling Rate (per Second): 150M
• Data Interface: Serial, SPI™
• Number Of Converters: 2
• Power Dissipation (max): 890mW
• Voltage Supply Source: Analog and Digital
• Operating Temperature: -40°C ~ 85°C
• Mounting Type: Surface Mount
• Package / Case: 64-LFCSP
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: AD9627-150EBZ - BOARD EVAL FOR AD9627-150AD9627-125EBZ - IC A/D 12BIT 125MSPS DL EVAL BRD
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

External Reference Operation
The use of an external reference may be necessary to enhance
the gain accuracy of the ADC or improve thermal drift charac-
teristics. Figure 54 shows the typical drift characteristics of the
internal reference in 1.0 V mode.
When the SENSE pin is tied to AVDD, the internal reference is
disabled, allowing the use of an external reference. An internal
reference buffer loads the external reference with an equivalent
6 kΩ load (see Figure 15). The internal buffer generates the
positive and negative full-scale references for the ADC core.
Therefore, the external reference must be limited to a maximum
of 1.0 V.
CLOCK INPUT CONSIDERATIONS
For optimum performance, the AD9627 sample clock inputs,
CLK+ and CLK−, should be clocked with a differential signal.
The signal is typically ac-coupled into the CLK+ and CLK− pins
via a transformer or capacitors. These pins are biased internally
(see Figure 55) and require no external bias.
Clock Input Options
The AD9627 has a very flexible clock input structure. Clock input
can be a CMOS, LVDS, LVPECL, or sine wave signal. Regardless of
the type of signal being used, clock source jitter is of the most
concern, as described in the Jitter Considerations section.
Figure 56 and Figure 57 show two preferred methods for clocking
the AD9627 (at clock rates up to 625 MHz). A low jitter clock
source is converted from a single-ended signal to a differential
signal using either an RF balun or an RF transformer.
–0.5
–1.0
–1.5
–2.0
–2.5
2.5
2.0
1.5
1.0
0.5
CLK+
0
–40
Figure 55. Equivalent Clock Input Circuit
–20
2pF
Figure 54. Typical VREF Drift
0
TEMPERATURE (°C)
AVDD
1.2V
20
40
60
2pF
CLK–
80
Rev. B | Page 29 of 76
The RF balun configuration is recommended for clock
frequencies between 125 MHz and 625 MHz, and the RF
transformer is recommended for clock frequencies from 10 MHz
to 200 MHz. The back-to-back Schottky diodes across the
transformer/balun secondary limit clock excursions into the
AD9627 to approximately 0.8 V p-p differential.
This helps prevent the large voltage swings of the clock from
feeding through to other portions of the AD9627 while preserving
the fast rise and fall times of the signal that are critical to a low
jitter performance.
If a low jitter clock source is not available, another option is to
ac couple a differential PECL signal to the sample clock input
pins, as shown in Figure 58. The
AD9513/AD9514/AD9515/AD9516
jitter performance.
A third option is to ac-couple a differential LVDS signal to the
sample clock input pins, as shown in Figure 59. The AD9510/
AD9511/AD9512/AD9513/AD9514/AD9515/AD9516 clock
drivers offer excellent jitter performance.
CLOCK
CLOCK
CLOCK
CLOCK
CLOCK
INPUT
INPUT
INPUT
INPUT
INPUT
CLOCK
INPUT
Figure 56. Transformer-Coupled Differential Clock (Up to 200 MHz)
50kΩ
50kΩ
Figure 57. Balun-Coupled Differential Clock (Up to 625 MHz)
Figure 59. Differential LVDS Sample Clock (Up to 625 MHz)
Figure 58. Differential PECL Sample Clock (Up to 625 MHz)
50Ω
0.1µF
50Ω
1nF
1nF
0.1µF
0.1µF
50kΩ
0.1µF
0.1µF
50kΩ
100Ω
ADT1–1WT, 1:1Z
Mini-Circuits
AD951x
PECL DRIVER
AD951x
LVDS DRIVER
XFMR
0.1µF
240Ω
®
0.1µF
0.1µF
0.1µF
0.1µF
AD9510/AD9511/AD9512/
SCHOTTKY
SCHOTTKY
HSMS2822
clock drivers offer excellent
HSMS2822
DIODES:
DIODES:
240Ω
100Ω
100Ω
0.1µF
0.1µF
0.1µF
0.1µF
CLK+
CLK–
AD9627
CLK+
CLK–
AD9627
ADC
CLK+
CLK–
CLK+
CLK–
AD9627
AD9627
AD9627
ADC
ADC
ADC