CS61584A-IQ3Z Cirrus Logic Inc, CS61584A-IQ3Z Datasheet - Page 33
![IC,Line Interface,QFP,64PIN,PLASTIC](/photos/6/80/68092/cs42888-dqz_sml.jpg)
CS61584A-IQ3Z
Manufacturer Part Number
CS61584A-IQ3Z
Description
IC,Line Interface,QFP,64PIN,PLASTIC
Manufacturer
Cirrus Logic Inc
Datasheet
1.CS61584A-IQ3Z.pdf
(54 pages)
Specifications of CS61584A-IQ3Z
Interface
Parallel/Serial
Voltage - Supply
3.3V, 5V
Package / Case
64-LQFP
Mounting Type
Surface Mount
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Applications
-
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Other names
598-1713
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
CS61584A-IQ3Z
Manufacturer:
Cirrus Logic Inc
Quantity:
10 000
Part Number:
CS61584A-IQ3Z
Manufacturer:
CIRRUS
Quantity:
20 000
Company:
Part Number:
CS61584A-IQ3ZR
Manufacturer:
Cirrus Logic Inc
Quantity:
10 000
Bypass Register: The Bypass register consists of a
single bit, and provides a serial path between J-TDI
and J-TDO, bypassing the BSR. This allows by-
passing specific devices during certain board-level
tests. This also reduces test access times by reduc-
ing the total number of shifts required from J-TDI
to J-TDO.
10.2 JTAG Instructions and Instruction
The instruction register (2 bits) allows the instruc-
tion to be shifted into the JTAG circuit. The in-
struction selects the test to be performed or the data
register to be accessed or both. The valid instruc-
tions are shifted in LSB first and are listed in
Table 12:
EXTEST Instruction: The EXTEST instruction al-
lows testing of off-chip circuitry and board-level
interconnect. EXTEST connects the BSR to the J-
TDI and J-TDO pins. The normal path between the
CS61584A logic and I/O pins is broken. The sig-
nals on the output pins are loaded from the BSR
and the signals on the input pins are loaded into the
BSR.
DS261PP5
DS261F1
MSB
31 28 27
0 0 0 0 0 1 1 0 0 1 1 0 1 1 1 0 0 0 0 1 0 0 0 0 1 1 0 0 1 0 0 1
31-28
27-14
13-12
11-1
0
4 bits
BIT #(s)
IR CODE
Register (IR)
Table 11. Device Identification Register
00
01
10
11
Version Number
Part Number
Derivative Code
Manufacturer Number
Constant Logic ‘1’
16 bits
EXTEST
SAMPLE/PRELOAD
IDCODE
BYPASS
Table 12.
Function
INSTRUCTION
12 11
11 bits
Total Bits
14
11
4
2
1
DS261PP5
LSB
1 0
SAMPLE/PRELOAD Instruction: The SAM-
PLE/PRELOAD instructions allows scanning of
the boundary-scan register without interfering with
the operation of the CS61584A. This instruction
connects the BSR to the J-TDI and J-TDO pins.
The normal path between the CS61584A logic and
its I/O pins is maintained. The signals on the I/O
pins are loaded into the BSR. Additionally, this in-
struction can be used to latch values into the digital
output pins.
IDCODE Instruction: The IDCODE instruction
connects the device identification register to the J-
TDO pin. The IDCODE instruction is forced into
the instruction register during the Test-Logic-Reset
controller state.The default instruction is IDCODE
after a device reset.
BYPASS Instruction: The BYPASS instruction
connects the minimum length bypass register be-
tween the J-TDI and J-TDO pins and allows data to
be shifted in the Shift-DR controller state.
10.3 JTAG TAP Controller
Figure 24 shows the state diagram for the TAP state
machine. A description of each state follows. Note
that the figure contains two main branches to ac-
cess either the data or instruction registers. The val-
ue shown next to each state transition in this figure
is the value present at J-TMS at each rising edge of
J-TCK.
10.4 Test-Logic-Reset State
In this state, the test logic is disabled to continue
normal operation of the device. During initializa-
tion, the CS61584A initializes the instruction reg-
ister with the IDCODE instruction.
Regardless of the original state of the controller,
the controller enters the Test-Logic-Reset state
when the J-TMS input is held high for at least five
rising edges of J-TCK. The controller remains in
this state while J-TMS is high. The CS61584A pro-
cessor automatically enters this state at power-up.
CS61584A
CS61584A
33
33