ISL65426EVAL1Z Intersil, ISL65426EVAL1Z Datasheet - Page 19

• Manufacturer Part Number: ISL65426EVAL1Z
• Description: ISL65426 EVAL BOARD 1 - RoHS COMPLIANT - QFN
• Manufacturer: Intersil

response, the output voltage initially deviates by an amount
shown in Equation 4.
The filter capacitor must have sufficiently low ESL and ESR
so that ΔV < ΔV
Most capacitor solutions rely on a mixture of high frequency
capacitors with relatively low capacitance in combination
with bulk capacitors having high capacitance but limited
high-frequency performance. Minimizing the ESL of the
high-frequency capacitors allows them to support the output
voltage as the current increases. Minimizing the ESR of the
bulk capacitors allows them to supply the increased current
with less output voltage deviation.
The ESR of the bulk capacitors also creates the majority of
the output voltage ripple. As the bulk capacitors sink and
source the inductor AC ripple current, a voltage develops
across the bulk capacitor V
The recommended load capacitance recommended is based
on Equation 6.
OUTPUT INDUCTOR SELECTION
Once the output capacitors are selected, the maximum
allowable ripple voltage, V
on the inductance. See Equation 7.
Since the output capacitors are supplying a decreasing
portion of the load current while the regulator recovers from
the transient, the capacitor voltage becomes slightly
depleted. The output inductors must be capable of assuming
the entire load current before the output voltage decreases
more than ΔV
Equation 8 gives the upper limit on output inductance for the
cases when the trailing edge of the current transient causes
the greater output voltage deviation than the leading edge.
Equation 9 addresses the leading edge. Normally, the
trailing edge dictates the inductance selection because duty
cycles are usually less than 50%. Nevertheless, both
inequalities should be evaluated, and inductance should be
governed based on the lower of the two results. In each
ΔV
V
L
C
PP
OUT
≥
≈
ESR
MAX
ESL
=
×
0.5
=
×
(
---------------------------------------------------- -
ESR
f
V
s
di
---- -
dt
×
IN
×
MAX
I
OUT
V
+
–
MAX
IN
×
[
V
ESR
. This places an upper limit on inductance.
MAX
OUT
×
(
---------------------------------------------------- -
V
.
V
IN
PP
)V
×
L
×
–
ΔI
MAX
×
100μF
OUT
V
f
PPMAX
]
OUT
s
PPMAX
×
19
V
)V
IN
OUT
, determines the lower limit
. See Equation 5.
(EQ. 4)
(EQ. 5)
(EQ. 6)
(EQ. 7)
ISL65426
equation, L is the output inductance and C is the total output
capacitance.
The other concern when selecting an output inductor is the
internally set current mode slope compensation. Designs
should not allow inductor ripple currents below 0.125 times
the maximum output current to prevent regulation issues. A
good rule of thumb for selection of the output inductance
value is 1/3 of the maximum load current for inductor ripple.
L
The rule of thumb value, see Equation 10, with fall between
the minimum inductance value calculated in Equation 7 and
the maximum values determined from Equations 8 and 9.
Input Capacitor Selection
Input capacitors are responsible for sourcing the AC
component of the input current flowing into the switching
power devices. Their RMS current capacity must be
sufficient to handle the AC component of the current drawn
by the switching power devices which is related to duty
cycle. The maximum RMS current required by the regulator
is closely approximated by Equation 11.
The important parameters to consider when selecting an
input capacitor are the voltage rating and the RMS current
rating. For reliable operation, select capacitors with voltage
ratings above the maximum input voltage. Their voltage
rating should be at least 1.25 times greater than the
maximum input voltage, while a voltage rating of 1.5 times is
a conservative guideline. The capacitor RMS current rating
should be higher than the largest RMS current required by
the circuit.
L
L
I
≅
RMS MAX
≤
≤
2 C V
------------------------ - ΔV
(
------------------------ - ΔV
(
-------------------------------------------------------------- -
1.25
V IN V OUT
V
⋅
(
(
IN
ΔI
ΔI
–
×
⋅
)
) C
)
2
2
f
⋅
s
O
=
×
I OUT
-----------------------------
V OUT
-----------------
) V OUT
V
MAX
×
MAX
IN
3
MAX
×
–
–
⎛
⎜
⎝
(
(
I
OUT MAX
ΔI ESR
ΔI ESR
⋅
⋅
)
)
2
+
⎛
⎝
V
----- -
12
1
IN
×
–
⎛
⎜
⎝
V IN V OUT
--------------------------------- -
V
O
L
⎞
⎠
–
×
f
s
November 14, 2006
×
V OUT
-----------------
V
(EQ. 10)
(EQ. 11)
IN
(EQ. 8)
(EQ. 9)
FN6340.1
⎞ 2
⎟
⎠
⎞
⎟
⎠