DRT2-OD32B Omron, DRT2-OD32B Datasheet - Page 309
DRT2-OD32B
Manufacturer Part Number
DRT2-OD32B
Description
32 Out Horiz MIL Connector NPN
Manufacturer
Omron
Datasheet
1.DRT2-OD16.pdf
(600 pages)
Specifications of DRT2-OD32B
Lead Free Status / Rohs Status
Lead free / RoHS Compliant
- Current page: 309 of 600
- Download datasheet (13Mb)
Mounting and Wiring Environment-resistive Slaves
Wiring I/O
Compatible Connectors
288
Note Refer to the OMRON Sensors Catalog (X42) for details on Sensor Connec-
Note The XS2G Connector Plug for Custom Cable Assembly (L-shaped type) and
Connect the I/O wiring to the Environment-resistive Terminal with the XS2-
series Round Waterproof Connectors listed in the following table.
Sensors that are pre-wired with a connector can be connected directly.
Refer to the catalog or manual for details on the device's pin arrangements
before connecting any device.
tions and Round Waterproof Connectors (Sensor I/O Connectors).
Use one of the following OMRON Y-joints when connecting a DRT2-HD16C(-
1), DRT2-HD16CL(-1), or DRT2-MD16CL(-1) Environment-resistive Terminal
with 16 inputs to sensors or limit switches, except when the sensor has diag-
nostic output.
XS2W-series L-shaped plug type cannot be connected to a Y-joint Connector,
because these connectors will cause interference with any Connectors
located beside them.
Sensor with Connector
Cable with connector on one end (male plug)
Cable with connectors on both ends (socket and plug)
Connector plug assembly (male)
(Crimp-connector or solder type)
Y-joint with plug/socket (connector on both ends)
Y-joint with plug/socket (without cable)
Sensor with Junction Connector
mal shutdown, so when a Power Supply Unit with a low-capacity rating or
instantaneous shutoff overcurrent protection is used, the load short-circuit
may not be detected. Always use a Power Supply Unit with a rating of 50
W or higher if it uses dropping overcurrent protection characteristic. Always
use a Power Supply Unit with a rating of 150 W or higher if it uses intermit-
tent overcurrent protection. The current limiter will protect the transistor
even if short-circuit detection is disabled.
XS2W-D42@-@81-A Cable with
round waterproof connector on
both ends (socket/plug)
XS2R-D426-@11-F Y-joint with plug/socket
(connector on both ends)
XS2R-D426-1 Y-joint with
plug/socket (without cable)
Connector
Connector
16 inputs
XS2G-D4@@
Sensor with lead wires
XS2H-D421-@80-A Cable with round
waterproof connector on one end (plug)
XS2R-D426-@11-F
XS2R-D426-1
XS2H-D421-@80-A
XS2W-D42@-@81-A
XS2G-D4@@
Model
Model
Section 6-6
Related parts for DRT2-OD32B
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
DRT2 Mix IO E-Con 8in/out PNP
Manufacturer:
Omron
Datasheet:
Part Number:
Description:
DRT2 16 OutMIL Conn Cable With
Manufacturer:
Omron
Datasheet:
Part Number:
Description:
DRT2 16 In MIL Connector NPN
Manufacturer:
Omron
Datasheet:
Part Number:
Description:
DRT2 16 In MIL Connector PNP
Manufacturer:
Omron
Datasheet:
Part Number:
Description:
DRT2 16 In MIL Conn Cable With
Manufacturer:
Omron
Datasheet:
Part Number:
Description:
DRT2 16 In MIL Conn Cable With
Manufacturer:
Omron
Datasheet:
Part Number:
Description:
DRT2 Mix IO E-Con8 In/out, NPN
Manufacturer:
Omron
Datasheet:
Part Number:
Description:
DRT2 8 Out TermOutal NPN
Manufacturer:
Omron
Datasheet:
Part Number:
Description:
G6S-2GLow Signal Relay
Manufacturer:
Omron Corporation
Datasheet:
Part Number:
Description:
Compact, Low-cost, SSR Switching 5 to 20 A
Manufacturer:
Omron Corporation
Datasheet:
Part Number:
Description:
Manufacturer:
Omron Corporation
Datasheet: