DRT2-OD32B Omron, DRT2-OD32B Datasheet - Page 94
DRT2-OD32B
Manufacturer Part Number
DRT2-OD32B
Description
32 Out Horiz MIL Connector NPN
Manufacturer
Omron
Datasheet
1.DRT2-OD16.pdf
(600 pages)
Specifications of DRT2-OD32B
Lead Free Status / Rohs Status
Lead free / RoHS Compliant
- Current page: 94 of 600
- Download datasheet (13Mb)
I/O Indicator Status when
Disconnection is Detected
Setting Using the
DeviceNet
Configurator
Functions of General-purpose Slaves and Environment-resistive Slaves
1,2,3...
Note
When a disconnection is detected, the Sensor Disconnected Flag in the Sta-
tus Area will turn ON. The Configurator or explicit messages can be used to
read the status of the Sensor Disconnected Flag, and to read the status of the
disconnected contact.
The Configurator or explicit messages can be used to enable or disable the
sensor disconnected detection for each contact. (Sensor disconnected detec-
tion is disabled in the factory setting.)
Disconnection of the signal line for three-wire sensors cannot be detected by
this function. (A disconnected power line can be detected, however.) Discon-
nection may be falsely detected for sensors (dry contacts such as limit
switches or relays, and some other two-wire proximity sensors) with a current
consumption of 0.3 mA or lower (0.5 mA or lower for Environment-resistive
Terminals), so always disable this function when using these sensors.
Environment-resistive Terminals
The box indicates the number of the corresponding connector.
1. Refer to SECTION 6 Environment-resistive Slaves for the position of the
2. For 16-point Input Units, the settings cannot be set to both enable and dis-
3. After a sensor disconnection is detected, a delay of up to 1.2 s will occur
Screw-less Clamp Terminals
The method used to set values from the DeviceNet Configurator (Ver. 2.20 or
later) is described here.
1. Turn ON the power to the DRT2-series Smart Slave.
2. From the Main Window, open the Network Configuration Window and dou-
Flashing
red.
Environment-resistive Terminal, Screw-less Clamp
Terminal
0 to 15
Flashing
red.
Discon-
nected
actual indicator.
able within the same connector.
before the Sensor Disconnected Flag turns ON.
ble-click or click the right mouse button over the icon of the DRT2-series
Smart Slave to be set. Select Parameter and Edit to display the Edit De-
vice Parameters Window.
Sensor
-A
OFF
-B
Is the sensor
connected properly?
Section 4-3
73
Related parts for DRT2-OD32B
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
DRT2 Mix IO E-Con 8in/out PNP
Manufacturer:
Omron
Datasheet:
Part Number:
Description:
DRT2 16 OutMIL Conn Cable With
Manufacturer:
Omron
Datasheet:
Part Number:
Description:
DRT2 16 In MIL Connector NPN
Manufacturer:
Omron
Datasheet:
Part Number:
Description:
DRT2 16 In MIL Connector PNP
Manufacturer:
Omron
Datasheet:
Part Number:
Description:
DRT2 16 In MIL Conn Cable With
Manufacturer:
Omron
Datasheet:
Part Number:
Description:
DRT2 16 In MIL Conn Cable With
Manufacturer:
Omron
Datasheet:
Part Number:
Description:
DRT2 Mix IO E-Con8 In/out, NPN
Manufacturer:
Omron
Datasheet:
Part Number:
Description:
DRT2 8 Out TermOutal NPN
Manufacturer:
Omron
Datasheet:
Part Number:
Description:
G6S-2GLow Signal Relay
Manufacturer:
Omron Corporation
Datasheet:
Part Number:
Description:
Compact, Low-cost, SSR Switching 5 to 20 A
Manufacturer:
Omron Corporation
Datasheet:
Part Number:
Description:
Manufacturer:
Omron Corporation
Datasheet: