DRT2-OD32BV-1 Omron, DRT2-OD32BV-1 Datasheet - Page 266
DRT2-OD32BV-1
Manufacturer Part Number
DRT2-OD32BV-1
Description
32 Out Vert MIL Connector PNP
Manufacturer
Omron
Datasheet
1.DRT2-OD16.pdf
(600 pages)
Specifications of DRT2-OD32BV-1
Lead Free Status / Rohs Status
Lead free / RoHS Compliant
- Current page: 266 of 600
- Download datasheet (13Mb)
6-4
6-4-1
Node Address
Settings
Baud Rate Setting
Output Hold/Clear
Setting
6-4-2
Input Specifications
Advanced Environment-resistive Terminals
Advanced Environment-resistive Terminals
Node Address, Baud Rate, and Output Hold/Clear Settings
Environment-resistive Terminals with 8 Transistor Inputs (IP67):
DRT2-ID08C (NPN) and DRT2-ID08C-1 (PNP)
Note
This section describes the Environment-resistive Terminal's node address
setting, baud rate settings, and hold/clear outputs for communications error
setting. These settings are made as follows:
Node address setting: Rotary switches
Baud rate setting: Automatic follow-up
Output hold/clear setting: Software switch
The node address of the Environment-resistive Terminal is set as a decimal,
using the top rotary switch for the ten's digit, and the bottom rotary switch for
the one's digit.
Any node address within the setting range can be used as long as it is not
already set for another node.
Refer to SECTION 5 General-purpose Slaves for details on setting from the
Configurator.
1. Setting the same node address for more than one node will cause a node
2. Always turn OFF the power (including the communications power supply)
The baud rate of the whole system is determined by the baud rate set for the
Master Unit. Setting the baud rate for each Unit is not required.
Use the Configurator to set the output hold/clear settings. The factory setting
is for outputs to be cleared. Refer to SECTION 5 General-purpose Slaves for
setting details.
Content
Network Power Volt-
age
Clear Button
Model
Internal I/O common NPN
Input points
address duplication error and communications will not start.
to the Slave before setting.
Item
Item
Displays the contents of the communications errors that
occurred.
Displays the power supply voltage being supplied when the
error occurred.
Clears the error history.
DRT2-ID08C
8 points (uses one word in the Master)
Specifications
Description
DRT2-ID08C-1
PNP
Section 6-4
245
Related parts for DRT2-OD32BV-1
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
DRT2 Mix IO E-Con 8in/out PNP
Manufacturer:
Omron
Datasheet:
Part Number:
Description:
DRT2 16 OutMIL Conn Cable With
Manufacturer:
Omron
Datasheet:
Part Number:
Description:
DRT2 16 In MIL Connector NPN
Manufacturer:
Omron
Datasheet:
Part Number:
Description:
DRT2 16 In MIL Connector PNP
Manufacturer:
Omron
Datasheet:
Part Number:
Description:
DRT2 16 In MIL Conn Cable With
Manufacturer:
Omron
Datasheet:
Part Number:
Description:
DRT2 16 In MIL Conn Cable With
Manufacturer:
Omron
Datasheet:
Part Number:
Description:
DRT2 Mix IO E-Con8 In/out, NPN
Manufacturer:
Omron
Datasheet:
Part Number:
Description:
DRT2 8 Out TermOutal NPN
Manufacturer:
Omron
Datasheet:
Part Number:
Description:
G6S-2GLow Signal Relay
Manufacturer:
Omron Corporation
Datasheet:
Part Number:
Description:
Compact, Low-cost, SSR Switching 5 to 20 A
Manufacturer:
Omron Corporation
Datasheet:
Part Number:
Description:
Manufacturer:
Omron Corporation
Datasheet: