WM8973LGEFL/V Wolfson Microelectronics, WM8973LGEFL/V Datasheet - Page 46
![Audio CODECs Stereo Codec with H/P Spkr](/photos/16/2/160214/qfn-32_sml.jpg)
WM8973LGEFL/V
Manufacturer Part Number
WM8973LGEFL/V
Description
Audio CODECs Stereo Codec with H/P Spkr
Manufacturer
Wolfson Microelectronics
Datasheets
1.WM8973LGEFLV.pdf
(57 pages)
2.WM8973LGEFLV.pdf
(63 pages)
3.WM8973LGEFLV.pdf
(61 pages)
4.WM8973LGEFLV.pdf
(57 pages)
Specifications of WM8973LGEFL/V
Maximum Operating Temperature
+ 85 C
Mounting Style
SMD/SMT
Package / Case
QFN-32
Minimum Operating Temperature
- 25 C
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
WM8973L
w
CLOCKING AND SAMPLE RATES
CLOCK OUTPUT
By default ADCLRC (pin 9) is the ADC word clock input/output. Under the control of ADCLRM[1:0],
register 27(1Bh) bits [8:7] the ADCLRC pin may be configured as a clock output. If ADCLRM is 01, 10
or 11 then ADCLRC pin is always an output even in slave mode or when TRI = ‘1’, (see Table 38).
The ADC then uses the DACLRC pin as its LRCLK in both master and slave modes.
Table 38 ADCLRC Clock Output
The WM8973L supports a wide range of master clock frequencies on the MCLK pin, and can
generate many commonly used audio sample rates directly from the master clock. The ADC and DAC
do not need to run at the same sample rate; several different combinations are possible.
There are two clocking modes:
Table 39 Clocking and Sample Rate Control
The clocking of the WM8973L is controlled using the CLKDIV2, USB, and SR control bits. Setting the
CLKDIV2 bit divides MCLK by two internally. The USB bit selects between ‘Normal’ and USB mode.
Each value of SR[4:0] selects one combination of MCLK division ratios and hence one combination of
sample rates (see next page). Since all sample rates are generated by dividing MCLK, their accuracy
depends on the accuracy of MCLK. If MCLK changes, the sample rates change proportionately.
Note that some sample rates (e.g. 44.1kHz in USB mode) are approximated, i.e. they differ from their
target value by a very small amount. This is not audible, as the maximum deviation is only 0.27%
(8.0214kHz instead of 8kHz in USB mode). By comparison, a half-tone step corresponds to a 5.9%
change in pitch.
The SR[4:0] bits must be set to configure the appropriate ADC and DAC sample rates in both master
and slave mode.
R27(1Bh)
Additional
Control (3)
R8 (08h)
Clocking and
Sample Rate
Control
REGISTER
ADDRESS
REGISTER
ADDRESS
‘Normal’ mode supports master clocks of 128f
(Note: f
USB mode supports 12MHz or 24MHz master clocks. This mode is intended for use in
systems with a USB interface, and eliminates the need for an external PLL to generate
another clock frequency for the audio CODEC.
s
refers to the ADC or DAC sample rate, whichever is faster)
[8:7] ADCLRM
BIT
6
5:1
0
BIT
LABEL
[1:0]
CLKDIV2
SR [4:0]
USB
DEFAULT
LABEL
00
Configures ADCLRC pin
00 = ADCLRC is ADC word clock input (slave
mode) or ADCLRC output (master mode)
01 = ADCLRC pin is MCLK output
10 = ADCLRC pin is MCLK / 5.5 output
11 = ADCLRC pin is MCLK / 6 output
0
00000
0
s
, 192f
DEFAULT
s
, 256f
s
, 384f
DESCRIPTION
Master Clock Divide by 2
1 = MCLK is divided by 2
0 = MCLK is not divided
Sample Rate Control
Clocking Mode Select
1 = USB Mode
0 = ‘Normal’ Mode
s
, and their multiples
PD, Rev 4.5, December 2011
DESCRIPTION
Production Data
46