WM8973LGEFL/V Wolfson Microelectronics, WM8973LGEFL/V Datasheet - Page 48
![Audio CODECs Stereo Codec with H/P Spkr](/photos/16/2/160214/qfn-32_sml.jpg)
WM8973LGEFL/V
Manufacturer Part Number
WM8973LGEFL/V
Description
Audio CODECs Stereo Codec with H/P Spkr
Manufacturer
Wolfson Microelectronics
Datasheets
1.WM8973LGEFLV.pdf
(57 pages)
2.WM8973LGEFLV.pdf
(63 pages)
3.WM8973LGEFLV.pdf
(61 pages)
4.WM8973LGEFLV.pdf
(57 pages)
Specifications of WM8973LGEFL/V
Maximum Operating Temperature
+ 85 C
Mounting Style
SMD/SMT
Package / Case
QFN-32
Minimum Operating Temperature
- 25 C
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
WM8973L
w
CONTROL INTERFACE
SELECTION OF CONTROL MODE
The WM8973L is controlled by writing to registers through a serial control interface. A control word
consists of 16 bits. The first 7 bits (B15 to B9) are address bits that select which control register is
accessed. The remaining 9 bits (B8 to B0) are data bits, corresponding to the 9 bits in each control
register. The control interface can operate as either a 3-wire or 2-wire MPU interface. The MODE pin
selects the interface format.
Table 41 Control Interface Mode Selection
3-WIRE SERIAL CONTROL MODE
In 3-wire mode, every rising edge of SCLK clocks in one data bit from the SDIN pin. A rising edge on
CSB latches in a complete control word consisting of the last 16 bits.
Figure 26 3-Wire Serial Control Interface
2-WIRE SERIAL CONTROL MODE
The WM8973L supports software control via a 2-wire serial bus. Many devices can be controlled by
the same bus, and each device has a unique 7-bit address (this is not the same as the 7-bit address
of each register in the WM8973L).
The WM8973L operates as a slave device only. The controller indicates the start of data transfer with
a high to low transition on SDIN while SCLK remains high. This indicates that a device address and
data will follow. All devices on the 2-wire bus respond to the start condition and shift in the next eight
bits on SDIN (7-bit address + Read/Write bit, MSB first). If the device address received matches the
address of the WM8973L and the R/W bit is ‘0’, indicating a write, then the WM8973L responds by
pulling SDIN low on the next clock pulse (ACK). If the address is not recognised or the R/W bit is ‘1’,
the WM8973L returns to the idle condition and wait for a new start condition and valid address.
Once the WM8973L has acknowledged a correct address, the controller sends the first byte of control
data (B15 to B8, i.e. the WM8973L register address plus the first bit of register data). The WM8973L
then acknowledges the first data byte by pulling SDIN low for one clock pulse. The controller then
sends the second byte of control data (B7 to B0, i.e. the remaining 8 bits of register data), and the
WM8973L acknowledges again by pulling SDIN low.
The transfer of data is complete when there is a low to high transition on SDIN while SCLK is high.
After receiving a complete address and data sequence the WM8973L returns to the idle state and
waits for another start condition. If a start or stop condition is detected out of sequence at any point
during data transfer (i.e. SDIN changes while SCLK is high), the device jumps to the idle condition.
Figure 27 2-Wire Serial Control Interface
SCLK
SDIN
SCLK
SDIN
CSB
MODE
High
START
Low
B15
B14
DEVICE ADDRESS
control register address
(7 BITS)
B13
B12
INTERFACE FORMAT
RD / WR
B11
BIT
2 wire
3 wire
B10
(LOW)
ACK
B9
register address and
CONTROL BYTE 1
1st register data bit
B8
(BITS 15 TO 8)
B7
B6
(LOW)
control register data bits
ACK
B5
CONTROL BYTE 2
B4
remaining 8 bits of
(BITS 7 TO 0)
register data
PD, Rev 4.5, December 2011
B3
B2
(LOW)
ACK
B1
Production Data
B0
latch
STOP
48