TDA8559TD NXP Semiconductors, TDA8559TD Datasheet - Page 31

• Manufacturer Part Number: TDA8559TD
• Description: Audio Amplifiers HEADPHONE AMP LV
• Manufacturer: NXP Semiconductors

Specifications of TDA8559TD

• Product: Class-AB
• Output Power: 140 mW
• Available Set Gain: 32 dB
• Thd Plus Noise: 0.05 %
• Operating Supply Voltage: 3 V
• Supply Current: 2.75 mA
• Maximum Power Dissipation: 1190 mW
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• Audio Load Resistance: 32 Ohms
• Input Bias Current (max): 300 nA
• Input Signal Type: Differential
• Minimum Operating Temperature: - 40 C
• Output Signal Type: Differential, Single
• Supply Type: Single
• Supply Voltage (max): 30 V
• Supply Voltage (min): 1.9 V
• Output Type: 1-Channel Mono or 2-Channel Stereo
• Package / Case: SOIC-16
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Other names: TDA8559T/N1,512

Philips Semiconductors
16. Soldering
TDA8559_3
Product data sheets
16.1 Introduction to soldering surface mount packages
16.2 Reflow soldering
16.3 Wave soldering
There is no soldering method that is ideal for all surface mount IC packages. Wave
soldering can still be used for certain surface mount ICs, but it is not suitable for fine pitch
SMDs. In these situations reflow soldering is recommended.
Reflow soldering requires solder paste (a suspension of fine solder particles, flux and
binding agent) to be applied to the printed-circuit board by screen printing, stencilling or
pressure-syringe dispensing before package placement. Driven by legislation and
environmental forces the worldwide use of lead-free solder pastes is increasing.
Several methods exist for reflowing; for example, convection or convection/infrared
heating in a conveyor type oven. Throughput times (preheating, soldering and cooling)
vary between 100 seconds and 200 seconds depending on heating method.
Typical reflow temperatures range from 215 C to 260 C depending on solder paste
material. The peak top-surface temperature of the packages should be kept below:
Table 8.
Table 9.
Moisture sensitivity precautions, as indicated on packing, must be respected at all times.
Conventional single wave soldering is not recommended for surface mount devices
(SMDs) or printed-circuit boards with a high component density, as solder bridging and
non-wetting can present major problems.
To overcome these problems the double-wave soldering method was specifically
developed.
If wave soldering is used the following conditions must be observed for optimal results:
Package thickness
< 2.5 mm
Package thickness
< 1.6 mm
1.6 mm to 2.5 mm
•
•
2.5 mm
2.5 mm
Use a double-wave soldering method comprising a turbulent wave with high upward
pressure followed by a smooth laminar wave.
For packages with leads on two sides and a pitch (e):
July 2004)
2004)
SnPb eutectic process - package peak reflow temperatures (from J-STD-020C
Pb-free process - package peak reflow temperatures (from J-STD-020C July
Volume mm
260 C + 0 C
260 C + 0 C
250 C + 0 C
Rev. 03 — 15 May 2006
Volume mm
240 C + 0/ 5 C
225 C + 0/ 5 C
3
< 350
3
< 350
Volume mm
2000
260 C + 0 C
250 C + 0 C
245 C + 0 C
Low-voltage stereo headphone amplifier
3
350 to
© Koninklijke Philips Electronics N.V. 2006. All rights reserved.
Volume mm
225 C + 0/ 5 C
225 C + 0/ 5 C
TDA8559T
Volume mm
260 C + 0 C
245 C + 0 C
245 C + 0 C
3
350
3
> 2000
31 of 36