LM193AJ/883 National Semiconductor, LM193AJ/883 Datasheet - Page 5

• Manufacturer Part Number: LM193AJ/883
• Description: Comparator Dual ±18V/36V 8-Pin CDIP Rail
• Manufacturer: National Semiconductor

Specifications of LM193AJ/883

• Package: 8CDIP
• Typical Response Time: 1.3 us
• Typical Response Time Range: 0.5 to 5 us
• Typical Voltage Gain Range: 90 to 110 dB
• Output Type: Open Collector
• Number Of Channels Per Chip: 2
• Minimum Single Supply Voltage: 2 V
• Power Supply Type: Single|Dual
• Number Of Elements: 2
• Technology: Bipolar
• Input Offset Voltage: 2mV
• Input Bias Current (typ): 1nA
• Response Time: 1.3us
• Single Supply Voltage (typ): 3/5/9/12/15/18/24/28V
• Dual Supply Voltage (typ): ±3/±5/±9/±12/±15V
• Supply Current (max): 1@5VmA
• Power Supply Requirement: Single/Dual
• Common Mode Rejection Ratio: 60dB
• Voltage Gain In Db: 106.02dB
• Power Supply Rejection Ratio: 60dB
• Single Supply Voltage (min): 2V
• Single Supply Voltage (max): 36V
• Dual Supply Voltage (min): ±1V
• Dual Supply Voltage (max): ±18V
• Power Dissipation: 780mW
• Operating Temp Range: -55C to 125C
• Operating Temperature Classification: Military
• Mounting: Through Hole
• Pin Count: 8
• Package Type: CDIP
• Lead Free Status / Rohs Status: Not Compliant

Electrical Characteristics
on the IC chip. This transistor action can cause the output voltages of the comparators to go to the V
duration that an input is driven negative. This is not destructive and normal output states will re-establish when the input voltage, which was negative, again returns
to a value greater than −0.3V.
Note 4: These specifications are limited to −55˚C≤T
−25˚C≤T
Note 5: The direction of the input current is out of the IC due to the PNP input stage. This current is essentially constant, independent of the state of the output so
no loading change exists on the reference or input lines.
Note 6: The input common-mode voltage or either input signal voltage should not be allowed to go negative by more than 0.3V. The upper end of the common-mode
voltage range is V
Note 7: The response time specified is for a 100 mV input step with 5 mV overdrive. For larger overdrive signals 300 ns can be obtained, see typical performance
characteristics section.
Note 8: Positive excursions of input voltage may exceed the power supply level. As long as the other voltage remains within the common-mode range, the
comparator will provide a proper output state. The low input voltage state must not be less than −0.3V (or 0.3V below the magnitude of the negative power supply,
if used).
Note 9: At output switch point, V
Note 10: Refer to RETS193AX for LM193AH military specifications and to RETS193X for LM193H military specifications.
Ordering Information
Note:
Note:
8-Pin Ceramic DIP
8-Pin Molded DIP
8-Bump (12 mils)
8-Pin Metal Can
8-Pin SOIC
micro SMD
*
**
Package
Also available per LM38510/11202
A
See STD Mil DWG 5962-94526
≤+85˚C and the LM393 temperature specifications are limited to 0˚C≤T
+
−1.5V at 25˚C, but either or both inputs can go to 36V without damage, independent of the magnitude of V
O
.1.4V, R
Temperature Range
−55˚C to 125˚C
−55˚C to 125˚C
−25˚C to 85˚C
−40˚C to 85˚C
−40˚C to 85˚C
−40˚C to 85˚C
0˚C to 70˚C
0˚C to 70˚C
0˚C to 70˚C
0˚C to 70˚C
S
=0Ω with V
(Continued)
A
+
≤+125˚C, for the LM193/LM193A. With the LM293 all temperature specifications are limited to
from 5V to 30V; and over the full input common-mode range (0V to V
5
A
≤+70˚C. The LM2903 is limited to −40˚C≤T
LM193AH-QMLV
LM193AJ-QMLV
LM193AH-MLS
LM193AJ-MLS
LM193AH/883
LM193H-MLS
LM193AJ/883
Part Number
LM193J/883
LM193H/883
LM2903ITLX
LM2903MX
LM2903ITL
LM393TLX
LM393MX
LM193AH
LM2903M
LM193H
LM2903N
LM393TL
LM393M
LM293H
LM393H
LM393N
+
*
voltage level (or to ground for a large overdrive) for the time
*
**
**
A
≤+85˚C.
+
.
+
−1.5V), at 25˚C.
NSC Drawing
TLA08AAA
H08C
M08A
N08E
J08A
www.national.com