P87C552SBAA NXP Semiconductors, P87C552SBAA Datasheet - Page 26

• Manufacturer Part Number: P87C552SBAA
• Description: MCU 8-Bit 87C 80C51 CISC 8KB EPROM 3.3V/5V 68-Pin PLCC Tube
• Manufacturer: NXP Semiconductors

Specifications of P87C552SBAA

• Package: 68PLCC
• Device Core: 80C51
• Family Name: 87C
• Maximum Speed: 16 MHz
• Operating Supply Voltage: 3.3|5 V
• Data Bus Width: 8 Bit
• Number Of Programmable I/os: 40
• Interface Type: I2C/UART
• On-chip Adc: 8-chx10-bit
• Number Of Timers: 3
• Ram Size: 256 Byte
• Program Memory Size: 8 KB
• Program Memory Type: EPROM
• Operating Temperature: 0 to 70 °C

between AVref+ and AVref–. If the analog input voltage range is from
Philips Semiconductors
10-Bit ADC Resolution and Analog Supply: Figure 23 shows how
the ADC is realized. The ADC has its own supply pins (AV
AV
DAC’s resistance-ladder. The ladder has 1023 equally spaced taps,
separated by a resistance of “R”. The first tap is located 0.5 x R
above Vref–, and the last tap is located 1.5 x R below Vref+. This
gives a total ladder resistance of 1024 x R. This structure ensures
that the DAC is monotonic and results in a symmetrical quantization
error as shown in Figure 25.
For input voltages between Vref– and (Vref–) + 1/2 LSB, the 10-bit
result of an A/D conversion will be 00 0000 0000B = 000H. For input
voltages between (Vref+) – 3/2 LSB and Vref+, the result of a
conversion will be 11 1111 1111B = 3FFH. AVref+ and AVref– may
be between AV
positive with respect to AVref–, and the input voltage (Vin) should be
2V to 4V, then 10-bit resolution can be obtained over this range if
AVref+ = 4V and AVref– = 2V.
The result can always be calculated from the following formula:
2003 Apr 01
80C51 8-bit microcontroller
8K/256 OTP, 8 channel 10 bit A/D, I
capture/compare, high I/O, low voltage (2.7 V to 5.5 V), low power
SS
Result + 1024
TOTAL RESISTANCE
=
=
) and two pins (Vref+ and Vref–) connected to each end of the
1023R + 2 x R/
1024R
DD
+ 0.2V and AV
R/2
R
R
R
R
R
R/2
AV
V
ref)
IN
* AV
AV
AV
* AV
ref+
ref–
SS
ref*
ref*
– 0.2V. AVref+ should be
Value 0000 0000 00
Value 1111 1111 11
V
V
ref
in
2
C, PWM,
Figure 23. ADC Realization
DD
COMPARATOR
and
–
+
is output for voltages V
is output for voltages (V
1023
1022
1021
3
2
1
0
DECODER
26
Power Reduction Modes
The 8XC552 has two reduced power modes of operation: the idle
mode and the power-down mode. These modes are entered by
setting bits in the PCON special function register. When the 8XC552
enters the idle mode, the following functions are disabled:
CPU
Timer T2
PWM0, PWM1
ADC
In idle mode, the following functions remain active:
Timer 0
Timer 1
Timer T3
SIO0 SIO1
External interrupts
When the 8XC552 enters the power-down mode, the oscillator is
stopped. The power-down mode is entered by setting the PD bit in
the PCON register. The PD bit can only be set if the EW input is tied
HIGH.
ref–
ref+
to (V
APPROXIMATION
– 3/2 LSB) to V
SUCCESSIVE
REGISTER
ref–
MSB
LSB
+ 1/2 LSB)
(halted)
(halted and reset)
(reset; outputs are high)
(may be enabled for operation in Idle mode
by setting bit AIDC (AUXR1.6) ).
ref+
APPROXIMATION
CONTROL LOGIC
SUCCESSIVE
P87C552
Product data
SU00961
START
READY