GNM1M2R71C104MA01D Murata, GNM1M2R71C104MA01D Datasheet - Page 60
![](/photos/30/39/303941/c5750_sml.jpg)
GNM1M2R71C104MA01D
Manufacturer Part Number
GNM1M2R71C104MA01D
Description
Manufacturer
Murata
Type
Ceramicr
Datasheet
1.GNM1M2R71C104MA01D.pdf
(220 pages)
Specifications of GNM1M2R71C104MA01D
Capacitance
.1uF
No. Of Capacitors
2
Tolerance (+ Or -)
20%
Voltage
16VDC
Number Of Terminals
4Terminal
Temp Coeff (dielectric)
X7R
Operating Temp Range
-55C to 125C
Mounting Style
Surface Mount
Package / Case
0504
Construction
SMT Chip
Failure Rate
Not Required
Product Height (mm)
0.6mm
Product Depth (mm)
1mm
Product Length (mm)
1.37mm
Lead Diameter (nom)
Not Requiredmm
Terminal Pitch
0.64mm
Lead Free Status / RoHS Status
Compliant
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
GNM1M2R71C104MA01D
Manufacturer:
MURATA
Quantity:
640 000
Company:
Part Number:
GNM1M2R71C104MA01D
Manufacturer:
MURATA
Quantity:
240 000
1
!Note
• This PDF catalog is downloaded from the website of Murata Manufacturing co., ltd. Therefore, it’s specifications are subject to change or our products in it may be discontinued without advance notice. Please check with our
• This PDF catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
sales representatives or product engineers before ordering.
!Note
58
No.
10
11 Vibration
12 Deflection
13
GRM Series Specifications and Test Methods (2) (Note1) Typical Inspection
Continued from the preceding page.
Adhesive Strength
of Termination
Solderability of
Termination
• Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.
• This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
GRM Series Specifications and Test Methods (2) (Note1) Typical Inspection
Item
Appearance
Capacitance
D.F.
Appearance
Capacitance
Change
No removal of the terminations or other defects should occur.
No defects or abnormalities
Within the specified tolerance
B1, B3, R1, R6*, R7*, C7, C8, E7, D7: 0.1 max.
C6: 0.125 max.
D8: 0.15 max.
F1, F5: 0.2 max.
*GRM31CR71E106: 0.125 max.
No marking defects
Within 10%
75% of the terminations is to be soldered evenly and
continuously.
GRM31CR6 0J/0G 107: 0.15 max.
R230
In case Non "*" is added in PNs table, please refer to GRM Series Specifications and Test Methods (1).
45
Capacitance meter
Specifications
In case "*" is added in PNs table, please refer to GRM Series Specifications and Test Methods (2).
20
Fig. 1a
Fig.3a
50
45
Pressurize
Please refer to individual specifications (our product specifications or the approval sheet).
Pressurizing
speed : 1.0mm/sec.
c
Flexure : V1
Baked electrode or
copper foil
Solder resist
(Note1) This Specifications and Test Methods indicates typical inspection.
Solder the capacitor on the test jig (glass epoxy board) shown
in Fig. 1a using an eutectic solder. Then apply 10N* force in
parallel with the test jig for 10 1sec.
The soldering should be done either with an iron or using the
reflow method and should be conducted with care so that the
soldering is uniform and free of defects such as heat shock.
*1N: GRM02, 2N: GRM03, 5N: GRM15/GRM18
Solder the capacitor on the test jig (glass epoxy board) in the
same manner and under the same conditions as (10).
The capacitor should be subjected to a simple harmonic motion
having a total amplitude of 1.5mm, the frequency being varied
uniformly between the approximate limits of 10 and 55Hz. The
frequency range, from 10 to 55Hz and return to 10Hz, should
be traversed in approximately 1 minute. This motion should be
applied for a period of 2 hours in each of 3 mutually
perpendicular directions (total of 6 hours).
Solder the capacitor on the test jig (glass epoxy board) shown
in Fig. 2a using an eutectic solder. Then apply a force in the
direction shown in Fig. 3a for 5 1 sec. The soldering should be
done by the reflow method and should be conducted with care
so that the soldering is uniform and free of defects such as heat
shock.
Immerse the capacitor in a solution of ethanol (JIS-K-8101) and
rosin (JIS-K-5902) (25% rosin in weight proportion).
Preheat at 80 to 120 C for 10 to 30 seconds.
After preheating, immerse in an eutectic solder solution for
2 0.5 seconds at 230 5 C or Sn-3.0Ag-0.5Cu solder solution
for 2 0.5 seconds at 245 5 C.
GRM02
GRM03
GRM15
GRM18
GRM21
GRM31
GRM32
GRM43
GRM55
GRM02
GRM03
GRM15
GRM18
GRM21
GRM31
GRM32
GRM43
GRM55
Type
Type
0.2
0.3
0.4
1.0
1.2
2.2
2.2
3.5
4.5
0.2
0.3
0.4
1.0
1.2
2.2
2.2
3.5
4.5
Test Method
a
a
Fig. 2a
100
Continued on the following page.
b
c
a
0.56
0.56
0.9
1.5
3.0
4.0
5.0
5.0
7.0
8.0
0.9
1.5
3.0
4.0
5.0
5.0
7.0
8.0
b
b
ø4.5
(GRM02/03/15: t: 0.8mm)
0.23
1.65
0.23
1.65
0.3
0.5
1.2
2.0
2.9
3.7
5.6
0.3
0.5
1.2
2.0
2.9
3.7
5.6
c
c
(in mm)
t: 1.6mm
C02E.pdf
09.9.18