82P2284BB IDT, Integrated Device Technology Inc, 82P2284BB Datasheet - Page 45

• Manufacturer Part Number: 82P2284BB
• Manufacturer: IDT, Integrated Device Technology Inc

Specifications of 82P2284BB

• Screening Level: Industrial
• Mounting: Surface Mount
• Operating Temperature (min): -40C
• Operating Temperature (max): 85C
• Lead Free Status / RoHS Status: Not Compliant

CRC Multi-Frame
the data stream. The structure of TS0 of the CRC Multi-Frame is illus-
trated in Table 18.
15) which are numbered from a Basic Frame with FAS. Each CRC Multi-
Frame can be divided into two Sub Multi-Frames (SMF I & SMF II).
initiates an 8 and a 400 ms timer to check the CRC Multi-Frame align-
ment signal if the CRCEN bit is ‘1’. The CRC Multi-Frame synchroniza-
tion is declared with a ‘0’ in the OOCMFV bit only if at least two CRC
Multi-Frame alignment patterns are found within 8 ms, with the interval
time of each pattern being a multiple of 2 ms. Then if the received CRC
Multi-Frame alignment signal does not meet its pattern, it will be indi-
cated by the CMFERI bit.
8ms with the interval time being a multiple of 2 ms, an offline search for
the Basic Frame alignment pattern will start which is indicated in the
OOOFV bit. The process is the same as shown in Figure 12. This offline
Table 18: The Structure Of TS0 In CRC Multi-Frame
Functional Description
IDT82P2284
Multi-Frame
The CRC Multi-Frame is provided to enhance the ability of verifying
A CRC Multi-Frame consists of 16 continuous Basic Frames (No. 0 –
After the Basic Frame has been synchronized, the Frame Processor
If the 2 CRC Multi-Frame alignment patterns can not be found within
CRC-4
SMF II
SMF I
SMF
Basic Frame
No. / Type
13 / NFAS
15 / NFAS
11 / NFAS
1 / NFAS
3 / NFAS
5 / NFAS
7 / NFAS
9 / NFAS
10 / FAS
12 / FAS
14 / FAS
0 / FAS
2 / FAS
4 / FAS
6 / FAS
8 / FAS
1 (Si bit)
C1
C2
C3
C4
C1
C2
C3
E1
C4
E2
0
0
1
0
1
1
2
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
45
3
0
A
0
A
0
A
0
A
0
A
0
A
0
A
0
A
The Si bit in each even frame is the CRC bit. Thus, there are C1, C2,
C3, C4 in each SMF. The C1 is the most significant bit, while the C4 is
the least significant bit. The Si bit in the first six odd frames is the CRC
Multi-Frame alignment pattern. Its pattern is ‘001011’. The Si bit in
Frame 13 and Frame 15 are E1 and E2 bits. The value of the E bits can
indicate the Far End Block Errors (FEBE).
operation searches in parallel with the pre-found Basic Frame synchro-
nization searching process. After the new Basic Frame synchronization
is found by this offline search, the 8 ms timer is restarted to check
whether the two CRC Multi-Frame alignment patterns are found within 8
ms, with the interval time of each pattern being a multiple of 2 ms again.
If the condition can not be met, the procedure will go on until the 400 ms
timer ends. If the condition still can not be met at that time and the Basic
Frame is still synchronized, the device declares by the C2NCIWV bit to
run under the CRC to non-CRC interworking process. In this process,
the CRC Multi-Frame alignment pattern can still be searched if the
C2NCIWCK bit is logic 1.
QUAD T1/E1/J1 LONG HAUL / SHORT HAUL TRANSCEIVER
The first bit of TS0 of each frame is called the International (Si) bit.
the Eight Bits in Timeslot 0
Sa4
Sa4
Sa4
Sa4
Sa4
Sa4
Sa4
Sa4
4
1
1
1
1
1
1
1
1
Sa5
Sa5
Sa5
Sa5
Sa5
Sa5
Sa5
Sa5
5
1
1
1
1
1
1
1
1
Sa6
Sa6
Sa6
Sa6
Sa6
Sa6
Sa6
Sa6
6
0
0
0
0
0
0
0
0
February 25, 2008
Sa7
Sa7
Sa7
Sa7
Sa7
Sa7
Sa7
Sa7
7
1
1
1
1
1
1
1
1
Sa8
Sa8
Sa8
Sa8
Sa8
Sa8
Sa8
Sa8
8
1
1
1
1
1
1
1
1