PIC24HJ12GP202-E/SO Microchip Technology, PIC24HJ12GP202-E/SO Datasheet - Page 101

• Manufacturer Part Number: PIC24HJ12GP202-E/SO
• Description: 12KB, Flash, 1024bytes-RAM, 40MIPS, 21I/O, 16-bit Family,nanoWatt 28 SOIC .300in
• Manufacturer: Microchip Technology
• Series: PIC® 24Hr

Specifications of PIC24HJ12GP202-E/SO

• Core Processor: PIC
• Core Size: 16-Bit
• Speed: 40 MIPs
• Connectivity: I²C, SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, POR, PWM, WDT
• Number Of I /o: 21
• Program Memory Size: 12KB (4K x 24)
• Program Memory Type: FLASH
• Ram Size: 1K x 8
• Voltage - Supply (vcc/vdd): 3 V ~ 3.6 V
• Data Converters: A/D 10x10b/12b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 125°C
• Package / Case: 28-SOIC (7.5mm Width)
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: AC164339 - MODULE SKT FOR PM3 28SOICDV164033 - KIT START EXPLORER 16 MPLAB ICD2
• Eeprom Size: -
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

10.4
A major challenge in general purpose devices is
providing the largest possible set of peripheral
features while minimizing the conflict of features on I/O
pins. The challenge is even greater on low-pin count
devices. In an application where more than one
peripheral must be assigned to a single pin,
inconvenient workarounds in application code or a
complete redesign may be the only option.
Peripheral pin select configuration enables peripheral
set selection and placement on a wide range of I/O
pins. By increasing the pinout options available on a
particular device, programmers can better tailor the
microcontroller to their entire application, rather than
trimming the application to fit the device.
The peripheral pin select configuration feature
operates over a fixed subset of digital I/O pins. Pro-
grammers can independently map the input and/or out-
put of most digital peripherals to any one of these I/O
pins. Peripheral pin select is performed in software,
and generally does not require the device to be
reprogrammed. Hardware safeguards are included that
prevent accidental or spurious changes to the
peripheral mapping, when it has been established.
10.4.1
The peripheral pin select feature is used with a range
of up to 16 pins. The number of available pins depends
on the particular device and its pin count. Pins that
support the peripheral pin select feature include the
designation ‘RPn’ in their full pin designation, where
‘RP’ designates a remappable peripheral and ‘n’ is the
remappable pin number.
10.4.2
Peripheral pin select features are controlled through
two sets of SFRs: one to map peripheral inputs, and
one to map outputs. Because they are separately
controlled, a particular peripheral’s input and output (if
the peripheral has both) can be placed on any
selectable function pin without constraint.
The association of a peripheral to a peripheral
selectable pin is handled in two different ways,
depending on whether an input or output is being
mapped.
© 2009 Microchip Technology Inc.
Peripheral Pin Select
AVAILABLE PINS
CONTROLLING PERIPHERAL PIN
SELECT
Preliminary
PIC24HJ12GP201/202
10.4.2.1
The inputs of the peripheral pin select options are
mapped on the basis of the peripheral. A control
register associated with a peripheral dictates the pin it
will be mapped to. The RPINRx registers are used to
configure peripheral input mapping (see Register 10-1
through Register 10-9). Each register contains sets of
5-bit fields, with each set associated with one of the
remappable
peripheral’s bit field with an appropriate 5-bit value
maps the RPn pin with that value to that peripheral.
For any given device, the valid range of values for any
bit field corresponds to the maximum number of
peripheral pin selections supported by the device.
Figure 10-2 Illustrates remappable pin selection for
U1RX input.
FIGURE 10-2:
Note:
RP 15
RP0
RP1
RP2
For input mapping only, the Peripheral Pin
Select (PPS) functionality does not have
priority over the TRISx settings. Therefore,
when configuring the RPx pin for input, the
corresponding bit in the TRISx register
must also be configured for input (i.e., set
to ‘1’).
Input Mapping
peripherals.
REMAPPABLE MUX
INPUT FOR U1RX
U1RXR<4:0>
15
0
1
2
Programming
U1RX input
to peripheral
DS70282D-page 99
a
given