S29JL032J70TFI420 Spansion Inc., S29JL032J70TFI420 Datasheet - Page 44

• Manufacturer Part Number: S29JL032J70TFI420
• Description: IC 3V 32M SIMULTANEOUS READ/WRITE FLASH
• Manufacturer: Spansion Inc.

Specifications of S29JL032J70TFI420

• Cell Type: NOR
• Density: 32Mb
• Access Time (max): 70ns
• Interface Type: Serial
• Boot Type: Bottom
• Address Bus: 22/21Bit
• Operating Supply Voltage (typ): 3/3.3V
• Operating Temp Range: -40C to 85C
• Package Type: TSOP
• Program/erase Volt (typ): 2.7 to 3.6V
• Sync/async: Asynchronous
• Operating Temperature Classification: Industrial
• Operating Supply Voltage (min): 2.7V
• Operating Supply Voltage (max): 3.6V
• Word Size: 8/16Bit
• Number Of Words: 4M/2M
• Supply Current: 16mA
• Mounting: Surface Mount
• Pin Count: 48
• Lead Free Status / Rohs Status: Supplier Unconfirmed

11.7
44
DQ3: Sector Erase Timer
After writing a sector erase command sequence, the system may read DQ3 to determine whether or not
erasure has begun. (The sector erase timer does not apply to the chip erase command.) If additional sectors
are selected for erasure, the entire time-out also applies after each additional sector erase command. When
the time-out period is complete, DQ3 switches from a “0” to a “1.” If the time between additional sector erase
commands from the system can be assumed to be less than 80 µs, the system need not monitor DQ3. See
also
After the sector erase command is written, the system should read the status of DQ7 (Data# Polling) or DQ6
(Toggle Bit I) to ensure that the device has accepted the command sequence, and then read DQ3. If DQ3 is
“1,” the Embedded Erase algorithm has begun; all further commands (except Erase Suspend) are ignored
until the erase operation is complete. If DQ3 is “0,” the device will accept additional sector erase commands.
To ensure the command has been accepted, the system software should check the status of DQ3 prior to and
following each subsequent sector erase command. If DQ3 is high on the second status check, the last
command might not have been accepted.
Table 11.1
Notes:
1. DQ5 switches to ‘1’ when an Embedded Program or Embedded Erase operation has exceeded the maximum timing limits. Refer to the
2. DQ7 and DQ2 require a valid address when reading status information. Refer to the appropriate subsection for further details.
3. When reading write operation status bits, the system must always provide the bank address where the Embedded Algorithm is in
Standard
Mode
Erase
Suspend
Mode
section on DQ5 for more information.
progress. The device outputs array data if the system addresses a non-busy bank.
Sector Erase Command Sequence on page
shows the status of DQ3 relative to the other status bits.
Embedded Program Algorithm
Embedded Erase
Algorithm
Erase-Suspend-
Read
Erase-Suspend-Program
Status
In busy erasing
sector
In not busy erasing
sector
Erase
Suspended Sector
Non-Erase
Suspended Sector
D a t a
Table 11.1 Write Operation Status
S29JL032J
S h e e t
(Note 2)
DQ7#
DQ7#
DQ7
Data
36.
0
0
1
( P r e l i m i n a r y )
No toggle
Toggle
Toggle
Toggle
Toggle
Data
DQ6
(Note 1)
DQ5
Data
0
0
0
0
0
S29JL032J_00_03 August 25, 2010
DQ3
Data
N/A
N/A
N/A
1
1
No toggle
No toggle
(Note 2)
Toggle
Toggle
DQ2
Data
N/A
RY/BY#
0
0
0
1
1
0