SCN2681AE1A44 NXP Semiconductors, SCN2681AE1A44 Datasheet - Page 12

• Manufacturer Part Number: SCN2681AE1A44
• Manufacturer: NXP Semiconductors

Specifications of SCN2681AE1A44

• Transmitter And Receiver Fifo Counter: No
• Operating Supply Voltage (typ): 5V
• Package Type: PLCC
• Operating Supply Voltage (max): 5.5V
• Operating Supply Voltage (min): 4.5V
• Mounting: Surface Mount
• Pin Count: 44
• Operating Temperature (min): -40C
• Operating Temperature (max): 85C
• Operating Temperature Classification: Industrial
• Number Of Channels: 2
• Lead Free Status / RoHS Status: Compliant

Philips Semiconductors
Table 2.
MR1A – Channel A Mode Register 1
MR1A is accessed when the Channel A MR pointer points to MR1.
The pointer is set to MR1 by RESET or by a ‘set pointer’ command
applied via CRA. After reading or writing MR1A, the pointer will point
to MR2A.
MR1A[7] – Channel A Receiver Request-to-Send Control
This bit controls the deactivation of the RTSAN output (OP0) by the
receiver. This output is normally asserted by setting OPR[0] and
negated by resetting OPR[0]. MR1A[7] = 1 causes RTSAN to be
negated upon receipt of a valid start bit if the Channel A FIFO is full.
However, OPR[0] is not reset and RTSAN will be asserted again
when an empty FIFO position is available. This feature can be used
for flow control to prevent overrun in the receiver by using the
RTSAN output signal to control the CTSN input of the transmitting
device.
MR1A[6] – Channel A Receiver Interrupt Select
This bit selects either the Channel A receiver ready status (RxRDY)
or the Channel A FIFO full status (FFULL) to be used for CPU
interrupts. It also causes the selected bit to be output on OP4 if it is
programmed as an interrupt output via the OPCR.
MR1A[5] – Channel A Error Mode Select
This bit select the operating mode of the three FIFOed status bits
(FE, PE, received break) for Channel A. In the ‘character’ mode,
status is provided on a character-by-character basis; the status
2004 Mar 18
Dual asynchronous receiver/transmitter (DUART)
CTUR
CTLR
IPCR
ACR
IMR
ISR
Register Bit Formats (Continued)
BRG SET
CHANGE
IN. PORT
CHANGE
SELECT
0 = set 1
1 = set 2
0 = No
1 = Yes
0 = No
1 = Yes
0 = Off
1 = On
C/T[15]
DELTA
INPUT
PORT
C/T[7]
BIT 7
BIT 7
BIT 7
BIT 7
BIT 7
BIT 7
IP 3
INT
BREAK B
BREAK B
0 = No
1 = Yes
0 = No
1 = Yes
0 = Off
1 = On
C/T[14]
DELTA
DELTA
DELTA
C/T[6]
BIT 6
BIT 6
BIT 6
BIT 6
BIT 6
BIT 6
IP 2
INT
MODE AND SOURCE
COUNTER/TIMER
See Table 4
FFULLB
FFULLB
0 = No
1 = Yes
RxRDY/
0 = No
1 = Yes
RxRDY/
0 = Off
1 = On
C/T[13]
DELTA
C/T[5]
BIT 5
BIT 5
BIT 5
BIT 5
BIT 5
BIT 5
IP 1
INT
TxRDYB
TxRDYB
0 = No
1 = Yes
0 = No
1 = Yes
0 = Off
1 = On
C/T[12]
DELTA
BIT 4
C/T[4]
BIT 4
BIT 4
BIT 4
BIT 4
BIT 4
12
IP 0
INT
applies only to the character at the top of the FIFO. In the ‘block”
mode, the status provided in the SR for these bits is the
accumulation (logical-OR) of the status for all characters coming to
the top of the FIFO since the last ‘reset error’ command for Channel
A was issued.
MR1A[4:3| – Channel A Parity Mode Select
If ‘with parity’ or ‘force parity’ is selected a parity bit is added to the
transmitted character and the receiver performs a parity check on
incoming data MR1A[4:3] + 11 selects Channel A to operate in the
special multidrop mode described in the Operation section.
MR1A[2] – Channel A Parity Type Select
This bit selects the parity type (odd or even) if the ‘with parity’ mode
is programmed by MR1A[4:3], and the polarity of the forced parity bit
if the ‘force parity’ mode is programmed. It has no effect if the ‘no
parity’ mode is programmed. In the special multidrop mode it selects
the polarity of the A/D bit.
MR1A[1:0] – Channel A Bits Per Character Select
This field selects the number of data bits per character to be
transmitted and received. The character length does not include the
start, parity, and stop bits.
COUNTER
COUNTER
0 = Off
1 = On
IP 3 INT
DELTA
0 = Low
1 = High
0 = No
1 = Yes
0 = Off
1 = On
READY
READY
C/T[11]
BIT 3
C/T[3]
BIT 3
BIT 3
BIT 3
BIT 3
BIT 3
IP 3
INT
BREAK A
BREAK A
0 = Off
1 = On
IP 2 INT
DELTA
0 = Low
1 = High
0 = No
1 = Yes
0 = Off
1 = On
C/T[10]
DELTA
DELTA
BIT 2
C/T[2]
BIT 2
BIT 2
BIT 2
BIT 2
BIT 2
IP 2
INT
IP 1 INT
0 = Off
1 = On
FFULLA
FFULLA
DELTA
0 = Low
1 = High
RxRDY/
0 = No
1 = Yes
RxRDY/
0 = Off
1 = On
BIT 1
C/T[9]
C/T[1]
BIT 1
BIT 1
BIT 1
BIT 1
BIT 1
IP 1
INT
SCN2681
Product data
0 = Off
1 = On
IP 0 INT
TxRDYA
TxRDYA
DELTA
0 = Low
1 = High
0 = No
1 = Yes
0 = Off
1 = On
BIT 0
C/T[8]
C/T[0]
BIT 0
BIT 0
BIT 0
BIT 0
BIT 0
IP 0
INT