ISP1504CBS,157 NXP Semiconductors, ISP1504CBS,157 Datasheet - Page 8
![RF Transceiver USB2.0 ULPI OTG](/photos/15/65/156561/hvqfn32_sml.jpg)
ISP1504CBS,157
Manufacturer Part Number
ISP1504CBS,157
Description
RF Transceiver USB2.0 ULPI OTG
Manufacturer
NXP Semiconductors
Datasheet
1.ISP1504ABS118.pdf
(83 pages)
Specifications of ISP1504CBS,157
Number Of Transceivers
1
Esd Protection
YeskV
Operating Supply Voltage (typ)
Not RequiredV
Operating Temperature Classification
Industrial
Operating Supply Voltage (max)
Not RequiredV
Operating Supply Voltage (min)
Not RequiredV
Pin Count
32
Mounting
Surface Mount
Operating Temperature (max)
85C
Operating Temperature (min)
-40C
Operating Supply Voltage
1.65 V to 3.6 V
Mounting Style
SMD/SMT
Package / Case
HVQFN-32
Lead Free Status / RoHS Status
Compliant
Other names
935278309157 ISP1504CBS
NXP Semiconductors
7. Functional description
ISP1504A_ISP1504C_3
Product data sheet
7.1 ULPI interface controller
7.2 USB data serializer and deserializer
7.3 Hi-Speed USB (USB 2.0) ATX
The ISP1504 provides a 12-pin interface that is compliant with UTMI+ Low Pin Interface
(ULPI) Specification Rev. 1.1 . This interface must be connected to the USB link.
The ULPI interface controller provides the following functions:
For more information on the ULPI protocol, see
The USB data serializer prepares data to transmit on the USB bus. To transmit data, the
USB link sends a transmit command and data on the ULPI bus. The serializer performs
parallel-to-serial conversion, bit stuffing and NRZI encoding. For packets with a PID, the
serializer adds a SYNC pattern to the start of the packet, and an EOP pattern to the end
of the packet. When the serializer is busy and cannot accept any more data, the ULPI
interface controller deasserts NXT.
The USB data deserializer decodes data received from the USB bus. When data is
received, the deserializer strips the SYNC and EOP patterns, and then performs
serial-to-parallel conversion, NRZI decoding and discarding of stuff bits on the data
payload. The ULPI interface controller sends data to the USB link by asserting DIR, and
then asserting NXT whenever a byte is ready. The deserializer also detects various
receive errors, including bit stuff errors, elasticity buffer underrun or overrun, and
byte-alignment errors.
The Hi-Speed USB ATX block is an analog front-end containing the circuitry needed to
transmit, receive and terminate the USB bus in high-speed, full-speed and low-speed, for
USB peripheral, host and OTG implementations. The following circuitry is included:
•
•
•
•
•
•
•
•
•
•
•
•
ULPI-compliant interface and register set
Allows full control over the USB peripheral, host and OTG functionality
Parses the USB transmit and receive data
Prioritizes the USB receive data, USB transmit data, interrupts and register operations
Low-power mode
Control of the V
V
6-pin serial mode and 3-pin serial mode
Generates RXCMDs; status updates
Maskable interrupts
Control over the ULPI bus state, allowing pins to 3-state or attach active weak
pull-down resistors
Differential drivers to transmit data at high-speed, full-speed and low-speed
BUS
monitoring, charging and discharging
BUS
Rev. 03 — 7 April 2008
charge pump or external source
ISP1504A; ISP1504C
Section
9.
ULPI HS USB OTG transceiver
© NXP B.V. 2008. All rights reserved.
7 of 82