DS90UR906QSQ National Semiconductor, DS90UR906QSQ Datasheet - Page 17
![no-image](/images/manufacturer_photos/0/4/469/national_semiconductor_sml.jpg)
DS90UR906QSQ
Manufacturer Part Number
DS90UR906QSQ
Description
Manufacturer
National Semiconductor
Datasheet
1.DS90UR906QSQ.pdf
(44 pages)
Specifications of DS90UR906QSQ
Number Of Elements
3
Diff. Input Low Threshold Volt
-50mV
Output Type
Deserializer
Power Dissipation
470mW
Operating Temp Range
-40C to 105C
Operating Temperature Classification
Industrial
Mounting
Surface Mount
Number Of Receivers
3
Number Of Drivers
24
Lead Free Status / RoHS Status
Not Compliant
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
DS90UR906QSQE/NOPB
Manufacturer:
TI/NSC
Quantity:
5 000
Part Number:
DS90UR906QSQE/NOPB
Manufacturer:
TI/德州仪器
Quantity:
20 000
V
V
V
V
I
t
t
t
t
t
C
Symbol
in
R
F
SU;DAT
HD;DAT
SP
IH
IL
HY
OL
in
DC and AC Serial Control Bus Characteristics
Over 3.3V supply and temperature ranges unless otherwise specified.
Note 1: “Absolute Maximum Ratings” indicate limits beyond which damage to the device may occur, including inoperability and degradation of device reliability
and/or performance. Functional operation of the device and/or non-degradation at the Absolute Maximum Ratings or other conditions beyond those indicated in
the Recommended Operating Conditions is not implied. The Recommended Operating Conditions indicate conditions at which the device is functional and the
device should not be operated beyond such conditions.
Note 2: The Electrical Characteristics tables list guaranteed specifications under the listed Recommended Operating Conditions except as otherwise modified
or specified by the Electrical Characteristics Conditions and/or Notes. Typical specifications are estimations only and are not guaranteed.
Note 3: Typical values represent most likely parametric norms at V
product characterization and are not guaranteed.
Note 4: Current into device pins is defined as positive. Current out of a device pin is defined as negative. Voltages are referenced to ground except VOD, ΔVOD,
VTH and VTL which are differential voltages.
Note 5: When the Serializer output is at TRI-STATE the Deserializer will lose PLL lock. Resynchronization / Relock must occur before data transfer require t
Note 6: t
Note 7: UI – Unit Interval is equivalent to one serialized data bit width (1UI = 1 / 28*PCLK). The UI scales with PCLK frequency.
Note 8: t
Note 9: t
Note 10: Supply noise testing was done with minimum capacitors on the PCB. A sinusoidal signal is AC coupled to the V
mVp-p measured at the device V
frequency on the Ser is less than 750 kHz. The Des on the other hand shows no error when the noise frequency is less than 400 kHz.
Note 11: Specification is guaranteed by characterization and is not tested in production.
Note 12: Specification is guaranteed by design and is not tested in production.
PLD
DPJ
DCCJ
Input High Level
Input Low Level Voltage
Input Hysteresis
Output Low Level Voltage,
(Note
SDA RiseTime – READ
SDA Fall Time – READ
Set Up Time — READ
Hold Up Time — READ
Input Filter
Input Capacitance
is the maximum amount the period is allowed to deviate over many samples.
and t
is the maximum amount of jitter between adjacent clock cycles.
11)
DDLT
Parameter
is the time required by the serializer and deserializer to obtain lock when exiting power-down state with an active PCLK.
DDn
pins. Bit error rate testing of input to the Ser and output of the Des with 10 meter cable shows no error when the noise
SDA and SCL
SDA and SCL
SDA, IOL = 1.25mA
SDA or SCL, Vin = V
SDA, RPU = X, Cb
SDA or SCL
DD
= 3.3V, Ta = +25 degC, and at the Recommended Operation Conditions at the time of
≤
Conditions
DDIO
400pF
17
or GND
GND
Min
2.2
-15
DDn
0
(1.8V) supply with amplitude = 100
Typ
>50
520
<5
40
25
55
50
V
Max
+15
0.8
0.4
www.national.com
DDIO
Units
mV
µA
pF
ns
ns
ns
ns
ns
PLD
V
V
V