DS90UR906QSQ National Semiconductor, DS90UR906QSQ Datasheet - Page 27
![no-image](/images/manufacturer_photos/0/4/469/national_semiconductor_sml.jpg)
DS90UR906QSQ
Manufacturer Part Number
DS90UR906QSQ
Description
Manufacturer
National Semiconductor
Datasheet
1.DS90UR906QSQ.pdf
(44 pages)
Specifications of DS90UR906QSQ
Number Of Elements
3
Diff. Input Low Threshold Volt
-50mV
Output Type
Deserializer
Power Dissipation
470mW
Operating Temp Range
-40C to 105C
Operating Temperature Classification
Industrial
Mounting
Surface Mount
Number Of Receivers
3
Number Of Drivers
24
Lead Free Status / RoHS Status
Not Compliant
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
DS90UR906QSQE/NOPB
Manufacturer:
TI/NSC
Quantity:
5 000
Part Number:
DS90UR906QSQE/NOPB
Manufacturer:
TI/德州仪器
Quantity:
20 000
1.8V or 3.3V VDDIO Operation
The Des parallel bus and Serial Bus Interface can operate
with 1.8 V or 3.3 V levels (V
ibility. The 1.8 V levels will offer a lower noise (EMI) and also
a system power savings.
Power Saving Features
Des — PowerDown Feature (PDB)
The Des has a PDB input pin to ENABLE or POWER DOWN
the device. This pin can be controlled by the system to save
power, disabling the Des when the display is not needed. An
auto detect mode is also available. In this mode, the PDB pin
is tied High and the Des will enter POWER DOWN when the
serial stream stops. When the serial stream starts up again,
the Des will lock to the input stream and assert the LOCK pin
and output valid data. In POWER DOWN mode, the Data and
PCLK output states are determined by the OSS_SEL status.
SSC3
H
H
H
H
H
H
H
H
L
L
L
L
L
L
L
L
FIGURE 22. SSCG Waveform
LH_MODE = H (5 - 20 MHz)
SSC2
H
H
H
H
H
H
H
H
L
L
L
L
L
L
L
L
DDIO
SSC[3:0] Inputs
TABLE 7. SSCG Configuration (LF_MODE = H) — Des Output
) for target (Display) compat-
SSC1
H
H
H
H
H
H
H
H
L
L
L
L
L
L
L
L
30102033
SSC0
H
H
H
H
H
H
H
H
L
L
L
L
L
L
L
L
27
Note – in POWER DOWN, the optional Serial Bus Control
Registers are RESET.
Des — Stop Stream SLEEP Feature
The Des will enter a low power SLEEP state when the input
serial stream is stopped. A STOP condition is detected when
the embedded clock bits are not present. When the serial
stream starts again, the Des will then lock to the incoming
signal and recover the data. Note – in STOP STREAM
SLEEP, the optional Serial Bus Control Registers values are
RETAINED.
Des — CLOCK-DATA RECOVERY STATUS FLAG (LOCK)
and OUTPUT STATE SELECT (OSS_SEL)
When PDB is driven HIGH, the CDR PLL begins locking to
the serial input and LOCK goes from TRI-STATE to LOW
(depending on the value of the OSS_SEL setting). After the
DS90UR906Q completes its lock sequence to the input serial
data, the LOCK output is driven HIGH, indicating valid data
and clock recovered from the serial input is available on the
parallel bus and PCLK outputs. The PCLK output is held at
its current state at the change from OSC_CLK (if this is en-
abled via OSC_SEL) to the recovered clock (or vice versa).
If there is a loss of clock from the input serial stream, LOCK
is driven Low and the state of the RGB/VS/HS/DE outputs are
based on the OSS_SEL setting (STRAP PIN configuration or
register).
Des — Oscillator Output — Optional
The Des provides an optional PCLK output when the input
clock (serial stream) has been lost. This is based on an inter-
nal oscillator. The frequency of the oscillator may be selected.
This feature may be controlled by the external pin or by reg-
ister. See
Table 9
fdev (%)
±0.5
±1.0
±1.5
±2.0
±0.5
±1.0
±1.5
±2.0
±0.5
±1.0
±1.5
±2.0
±0.5
±1.0
±1.5
Off
and
Table
Result
10.
fmod (kHz)
PCLK/620
PCLK/370
PCLK/258
PCLK/192
Off
www.national.com