M69AW048BL70ZB8T STMicroelectronics, M69AW048BL70ZB8T Datasheet - Page 8
![no-image](/images/manufacturer_photos/0/6/637/stmicroelectronics_sml.jpg)
M69AW048BL70ZB8T
Manufacturer Part Number
M69AW048BL70ZB8T
Description
Manufacturer
STMicroelectronics
Datasheet
1.M69AW048BL70ZB8T.pdf
(29 pages)
Specifications of M69AW048BL70ZB8T
Operating Temperature (max)
85C
Mounting
Surface Mount
Operating Temperature Classification
Commercial
Lead Free Status / RoHS Status
Not Compliant
M69AW048B
OPERATION
Operational modes are determined by device con-
trol inputs W, E1, E2, LB and UB as summarized
in the Operating Modes table (see
2., Operating
Power-Up Sequence
Because the internal control logic of the
M69AW048B needs to be initialized, the following
Power-Up procedure must be followed before the
memory is used:
See also
AC waveforms.
Read Mode
The device is in Read mode when:
The time taken to enter Read mode (t
or t
was the last to reach the appropriate level.
Data out (DQ15-DQ0) may be indeterminate dur-
ing t
valid during t
and
details of when the outputs become valid.
Write Mode
The device is in Write mode when
The Write cycle begins just after the event (the fall-
ing edge) that causes the last of these conditions
to become true (t
The Write cycle is terminated by the rising edge of
Write Enable (W) or Chip Enable (E1), whichever
occurs first.
If the device is in Write mode (Chip Enable (E1) is
Low, Output Enable (G) is Low, Upper Byte En-
able (UB) and/or Lower Byte Enable (LB) is Low,
then Write Enable (W) will return the outputs to
high impedance within t
Care must be taken to avoid bus contention in this
type of operation. Data input must be valid for t
VWH
for t
(E1), whichever occurs first, and remain valid for
t
8/29
BHDZ,
BLQV
–
–
–
–
–
–
–
–
ELQX
DVEH
Table 11., Read Mode AC
before the rising edge of Write Enable (W), or
t
WHDZ
Apply power and wait for V
Wait 300µs while driving both Chip Enable
signals (E1 and E2) High.
Write Enable (W) is High and
Output Enable (G) Low and
the two Chip Enable signals are asserted
(E1 is Low, and E2 is High).
Write Enable (W) is Low and
Chip Enable (E1) is Low and E2 is High
at least one of Upper Byte Enable (UB)
and Lower Byte Enable (LB) is Low.
) depends on which of the above signals
, t
Figure 24.
before the rising edge of Chip Enable
GLQX
, t
AVQV
Modes).
EHDZ
and t
AVWL
. See Figures 7, 8, 9,
.
for details on the Power-Up
BLQX
or t
WHDZ
AVEL
but data will always be
Characteristics, for
of its rising edge.
or t
AVBL
CC
ELQV
to stabilize,
).
10
, t
and
Table
GLQV
11
D-
See Figures 12, 13, 14, 15,
12., Write Mode AC
when the outputs become valid.
Standby Mode
The device is in Standby mode when:
The input/output buffers and the decoding/control
logic are switched off, but the dynamic array con-
tinues to be refreshed. In this mode, the memory
current consumption, I
remains valid.
See Figures
Down Mode AC
when the outputs become valid.
Power-down Modes
Description of Power-Down Modes. The
M69AW048B has four Power-down modes, Deep
Power-Down, 4 Mbit Partial Array Refresh, 8 Mbit
Partial Array Refresh, and 16 Mbit Partial Array
Refresh (see
These can be entered using a series of read and
write operations. Each mode has following fea-
tures. The default state is Deep Power-Down and
it is the lowest power consumption but all data will
be lost once E2 is brought Low for Power-down.
No sequence is required to put the device in Deep
Power-Down mode after Power-up.
The device is in one of the Power-down modes
when:
All the device logic is switched off and all internal
operations are suspended. This gives the lowest
power consumption. In this operating mode, no re-
fresh is performed, and data is lost if the duration
is longer than 10ns. This mode is useful for those
applications where the data contents are no longer
needed, and can be lost, but where reduced cur-
rent consumption is of major importance.
Power-Down Program Sequence. The Power-
Down Program sequence is used to program the
Power-Down Configuration. It requires a total of
six read and write operations, with specific ad-
dresses and data. Between each read or write op-
eration the device must be in Standby mode.
Table 4.
Byte at the highest memory address (MSB) is read.
In the second and third cycles, the data (RDa) read
by first cycle are written back. If the third cycle is
written into a different address, the sequence is
aborted, and the data written by the third cycle is
valid as in a normal write operation. In the fourth
and fifth cycles, the Power-Down Configuration
data is written. The data of the fourth cycle must be
–
–
–
Chip Enable (E1) is High and
Chip Enable (E2) is High
Chip Enable (E2) is Low
shows the sequence. In the first cycle, the
Table 4.
17
and
Characteristics, for details of
Characteristics, for details of
SB
Table 13., Standby/Power-
and
, is reduced, and the data
Figure
16
and
22.).
17
and
Table