HFCT-5963NL Avago Technologies US Inc., HFCT-5963NL Datasheet - Page 11
![](/photos/31/35/313527/5988-9971en_sml.jpg)
HFCT-5963NL
Manufacturer Part Number
HFCT-5963NL
Description
Manufacturer
Avago Technologies US Inc.
Datasheet
1.HFCT-5963NL.pdf
(16 pages)
Specifications of HFCT-5963NL
Optical Fiber Type
TX/RX
Data Transfer Rate
155Mbps
Optical Rise Time
2ns
Optical Fall Time
2ns
Operating Temperature Classification
Commercial
Peak Wavelength
1360/1580nm
Package Type
DIP With Connector
Operating Supply Voltage (min)
3.1V
Operating Supply Voltage (typ)
3.3V
Operating Supply Voltage (max)
3.5V
Output Current
50mA
Operating Temp Range
-5C to 70C
Mounting
Snap Fit To Panel
Pin Count
10
Lead Free Status / RoHS Status
Compliant
Regulatory Compliance
The Regulatory Compliance for transceiver performance
is shown in Table 1. The overall equipment design will
determine the certification level. The transceiver per-
formance is offered as a figure of merit to assist the de-
signer in considering their use in equipment designs.
Electrostatic Discharge (ESD)
There are two design cases in which immunity to ESD
damage is important.
The first case is during handling of the transceiver prior
to mounting it on the circuit board. It is important to
use normal ESD handling precautions for ESD sensitive
devices. These precautions include using grounded
wrist straps, work benches, and floor mats in ESD con-
trolled areas.
The second case to consider is static discharges to
the exterior of the equipment chassis containing the
transceiver parts. To the extent that the LC connector
receptacle is exposed to the outside of the equipment
chassis it may be subject to whatever system-level ESD
test criteria that the equipment is intended to meet.
Electromagnetic Interference (EMI)
Most equipment designs utilizing these high-speed
transceivers from Avago Technologies will be required
to meet FCC regulations in the United States, CENELEC
EN55022 (CISPR 22) in Europe and VCCI in Japan. Refer
to EMI section (page 9) for more details.
Table 1: Regulatory Compliance - Targeted Specification
11
Feature
Electrostatic Discharge (ESD)
to the Electrical Pins
Electrostatic Discharge (ESD)
to the LC Receptacle
Electromagnetic Interference
(EMI)
Immunity
Laser Eye Safety and
Equipment Type Testing
Component
Recognition
Test Method
MIL-STD-883
Method 3015
Variation of IEC 61000-4-2
FCC Class B
Variation of IEC 61000-4-3
FDA CDRH 21-CFR 1040
Class 1
IEC 60825-1
Amendment 2 2001-01
Underwriters Laboratories and
Canadian Standards Association
Joint Component Recognition for
Information Technology Equip-
ment Including Electrical Business
Equipment.
Immunity
Transceivers will be subject to radio-frequency elec-
tromagnetic fields following the IEC 61000-4-3 test
method.
Eye Safety
These laser-based transceivers are classified as AEL Class
I (U.S. 21 CFR(J) and AEL Class 1 per EN 60825-1 (+A11).
They are eye safe when used within the data sheet lim-
its per CDRH. They are also eye safe under normal oper-
ating conditions and under all reasonably foreseeable
single fault conditions per EN60825-1. Avago Technolo-
gies has tested the transceiver design for compliance
with the requirements listed below under normal op-
erating conditions and under single fault conditions
where applicable. TUV Rheinland has granted certifica-
tion to these transceivers for laser eye safety and use
in EN 60825-2 applications. Their performance enables
the transceivers to be used without concern for eye
safety up to 3.5 V transmitter V
Performance
Class 1 (>500 V).
Tested to 8 kV contact discharge.
Margins are dependent on customer board and chassis
designs.
Typically show no measurable effect from a 10 V/m field
swept from 27 to 1000 MHz applied to the transceiver with-
out a chassis enclosure.
Accession Number:
License Number:
UL File Number: E173874, 01SC14051
HFCT-5963TL/TG/ATL/ATG ) 933/510201/02 18 Jan. 2002
HFCT-5961NL/NG ) 933/510116/01 26 July 2001
HFCT-5961TL/TG/ATL/ATG ) 9521220-47
HFCT-5961NL/NG ) 9521220-46
CC
.