1382350-1 TE Connectivity, 1382350-1 Datasheet - Page 3

• Manufacturer Part Number: 1382350-1
• Manufacturer: TE Connectivity

Specifications of 1382350-1

• Optical Fiber Type: TX/RX
• Data Transfer Rate: 1250Mbps
• Optical Rise Time: 0.26ns
• Optical Fall Time: 0.26ns
• Jitter: 0.08ns
• Operating Temperature Classification: Commercial
• Peak Wavelength: 845nm
• Package Type: SFP MSA
• Operating Supply Voltage (min): 3.135V
• Operating Supply Voltage (typ): 3.3V
• Operating Supply Voltage (max): 3.465V
• Operating Temp Range: 0C to 70C
• Mounting: Snap Fit To Panel
• Lead Free Status / RoHS Status: Supplier Unconfirmed

©
For drawings, technical data or samples, contact your Tyco Electronics sales engineer, call 1-800-522-6752, or visit our Website at:
http://www.tycoelectronics.com/fiberoptics. Specifications subject to change. Consult Tyco Electronics for latest specifications.
Gigabit Ethernet Multimode
SFP MT-RJ Transceiver
Part Number 1382350-1
Copyright 2003 by Tyco Electronics Corporation. All Rights Reserved. AMP and Tyco are trademarks. Dimensions are in millimeters with inches
(if shown) in brackets. Other products, logos, and Company names mentioned herein may be trademarks of their respective owners.
Gigabit Ethernet Multimode SFP MT-RJ Transceiver
Receiver Performance Specifications:
(TC=0 to 70°C, V
Parameter
Operating Data Rate
Average Receive Power
Receive Sensitivity
Stressed Receive
Sensitivity
Electrical 3 dB Cut-Off
Optical wavelength
Deterministic Jitter
Total Jitter
Return Loss
Receiver Loss of Signal
Output Voltage
Rx LOS Power Levels
(avg.)
Power Supply Voltage
Supply Current
Operating Temperature
Note: All optical measurements made through a short patch cable, between 2 and 5 meters in length, using 62.5 µm
1.
2.
3.
4.
5.
50 µm Fiber
62.5 µm Fiber
Assert
Deassert
Assert
Deassert
Hysteresis
multimode fiber unless stated otherwise.
Minimum average optical input power (receive sensitivity) at which the BER is less than 10E-12 measured with
a 1.25 G Baud Rate 2E7 - 1 NRZ PRBS data pattern.
Per IEEE 802.3Z Gigabit Ethernet Standard.
Return loss measured per TIA/EIA 455-107.
This is an open drain output that should be pulled up with a 4.7K ohm - 10K ohm resistor on the host board.
Pull-up voltage level should be between 2.0 V and Vcc + 0.3 V per the SFP MSA.
DJ and TJ measured per IEEE 802.3Z Gigabit Ethernet Standard.
CC
-V
EE
=3.135 to 3.465V DC)
V CC - V EE
Symbol
3 dB f c
LOS
I CC
VD
P D
T C
P
DJ
VA
P A
λ
TJ
–
–
–
–
IN
IN
Notes
1
2
2
2
–
5
5
3
4
4
–
–
–
–
–
–
3.135
-13.5
-12.5
Min
770
-17
-30
0.5
12
–
–
–
–
–
2
0
–
–
0
(Continued)
http://www.tycoelectronics.com/fiberoptics
Typ
3.3
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
PDF Datasheet 1654843
V
3.465
Max
1.25
CC
860
170
266
100
-17
1.5
0.8
70
0
–
–
–
–
–
–
+ .3
Only available as PDF at:
Revised 11-03
Units
Gb/s
dBm
dBm
dBm
dBm
GHz
dBm
dBm
mA
nm
dB
dB
ps
ps
°C
V
V
V
3