SI3210-FTR Silicon Laboratories Inc, SI3210-FTR Datasheet - Page 124

• Manufacturer Part Number: SI3210-FTR
• Description: SLIC 1-CH 60dB 41mA 3.3V/5V 38-Pin TSSOP T/R
• Manufacturer: Silicon Laboratories Inc
• Series: ProSLIC®r

Specifications of SI3210-FTR

• Package: 38TSSOP
• Number Of Channels Per Chip: 1
• Polarity Reversal: Yes
• Longitudinal Balanced: 60 dB
• Loop Current: 41 mA
• Minimum Operating Supply Voltage: 3.13 V
• Typical Operating Supply Voltage: 3.3|5 V
• Typical Supply Current: 88 mA
• Function: Subscriber Line Interface Concept (SLIC), CODEC
• Interface: PCM, SPI
• Number Of Circuits: 1
• Voltage - Supply: 3.3V, 5V
• Current - Supply: 88mA
• Power (watts): 700mW
• Operating Temperature: 0°C ~ 70°C
• Mounting Type: Surface Mount
• Package / Case: 38-TSSOP
• Includes: BORSCHT Functions, DTMF Generation and Decoding, FSK Generation, Pulse Metering Generation, Voice Loopback Test Modes
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

Si3210/Si3211
4.5. FSK Control
For detailed instructions on FSK signal generation, refer
to “Application Note 32: FSK Generation” (AN32).
These registers support enhanced FSK generation
mode, which is enabled by setting FSKEN = 1 (direct
Register 108, bit 6) and REL = 1 (direct Register 32,
bit 6).
124
Addr. D15
Addr.
100
101
102
103
104
100
101
102
103
104
99
99
FSK Amplitude Coefficient for Space.
When FSKEN = 1 and REL = 1, this register sets the amplitude to be used when gener-
ating a space or “0”. When the active timer (OAT1) expires, the value of this register is
loaded into oscillator 1 instead of OSC1X.
FSK Frequency Coefficient for Space.
When FSKEN = 1 and REL = 1, this register sets the frequency to be used when gener-
ating a space or “0”. When the active timer (OAT1) expires, the value of this register is
loaded into oscillator 1 instead of OSC1.
FSK Amplitude Coefficient for Mark.
When FSKEN = 1 and REL = 1, this register sets the amplitude to be used when gener-
ating a mark or “1”. When the active timer (OAT1) expires, the value of this register is
loaded into oscillator 1 instead of OSC1X.
FSK Frequency Coefficient for Mark.
When FSKEN = 1 and REL = 1, this register sets the frequency to be used when gener-
ating a mark or “1”. When the active timer (OAT1) expires, the value of this register is
loaded into oscillator 1 instead of OSC1.
FSK Transition Parameter from 0 to 1.
When FSKEN = 1 and REL = 1, this register defines a gain correction factor that is
applied to signal amplitude when transitioning from a space (0) to a mark (1).
FSK Transition Parameter from 1 to 0.
When FSKEN = 1 and REL = 1, this register defines a gain correction factor that is
applied to signal amplitude when transitioning from a mark (1) to a space (0).
D14
D13
Table 46. FSK Control Indirect Registers Description
Table 45. FSK Control Indirect Registers Summary
D12
D11
D10
Description
D9
Rev. 1.45
FSK0X[15:0]
FSK1X[15:0]
FSK01[15:0]
FSK10[15:0]
FSK0[15:0]
FSK1[15:0]
D8
D7
D6
D5
D4
D3
D2
Reference Page
42 and AN32
42 and AN32
42 and AN32
42 and AN32
42 and AN32
42 and AN32
D1
D0