PAXLVD00 Red Lion Controls, PAXLVD00 Datasheet - Page 4

• Manufacturer Part Number: PAXLVD00
• Description: VOLTMETER DC 3 1/2-DIGIT
• Manufacturer: Red Lion Controls
• Series: PAX®LITEr
• Type: Voltmeterr

Specifications of PAXLVD00

• Measuring Range: 0 ~ 300V
• Display Style: Red Characters, Black Background
• Display Type: LED
• Display Face Size: 3.80" L x 1.95" W (96.5 x 49.5mm)
• Display Digits: 3.5
• Display Digits - Height: 0.560" (14.22mm)
• Backlight: Without
• Mounting Type: Panel Mount
• Termination: Terminal Block
• Voltage - Supply: 115VAC,230 VAC
• No. Of Digits / Alpha: 3-1/2
• Meter Function: DC Voltmeter
• Meter Range: 1.999V To 300V
• Digit Height: 14.2mm
• Power Consumption: 6VA
• Operating Temperature Range: 0°C To +60°C
• Supply Voltage Ac, Min: 115V
• Accuracy: ±0.1% %
• Connection Type: Cage-Clamp
• Cut Out, Panel: 3.62×1.77 "
• Dimensions: 4.2"L×3.8"W×1.95"H
• Display Digit Height: 0.56 "
• Display Resolution: 1 mV to 1 V
• Function: Voltage
• Meter Type: Panel
• Number Of Digits: 3-1/2
• Primary Type: Electronic
• Range, Measurement: 1.999 to 300 VDC
• Special Features: Multi-Range Unit
• Standards: CE Marked, cUL Recognized
• Temperature, Operating: 0 to 60 °C
• Voltage, Input: 1.999 to 300 V
• Voltage, Supply: 115/230 VAC
• Character Size: 0.56"
• Display Font Color: Red
• Rohs Compliant: Yes
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant, Lead free / RoHS Compliant
• Other names: RLC107

Installation
unit is intended to be mounted into an enclosed panel. Prepare the panel cutout
to the dimensions shown. Remove the panel latch from the unit. Slide the panel
gasket over the rear of the unit to the back of the bezel. The unit should be
installed fully assembled. Insert the unit into the panel cutout.
changed prior to applying power. To access the input jumper and switches,
remove the meter base from the case by firmly squeezing and pulling back on
the side rear finger tabs. This should lower the latch below the case slot (which
is located just in front of the finger tabs). It is recommended to release the latch
on one side, then start the other side latch.
Power Selection Switch
Input Range Jumper
proper input range that will be high enough to avoid input signal overload. It is
important that only one jumper position is used at a time. Avoid placing a jumper
across two different input ranges.
PAXLI Jumper Selection
1.0 I
2.0 S
BEZEL
The PAX meets NEMA 4X/IP65 requirements when properly installed. The
The meter has an input jumper and switches, which must be checked and/or
A jumper is used for selection of the voltage or current input range. Select the
PANEL
GASKET
proper voltage before powering the meter. The meter is shipped
from the factory in the 230 VAC position.
Caution: Insure the AC power selection switch is set for the
NSTALLING THE
JUMPER IN
THIS AREA!
ETTING THE
ONLY ONE
LATCHING
SLOTS
JUMPER SELECTIONS
The
INPUT RANGE JUMPER
REAR TERMINALS
indicates factory setting.
PANEL
CURRENT
±199.9µA
/199.9mV
±1.999mA
±19.99mA
±199.9mA
±1.999A
PANEL
MOUNTING
SCREWS
J
UMPERS AND
PANEL
LATCH
M
LATCHING
TABS
ETER
4
so that the tabs of the panel latch engage in the slots on the case. The panel latch
should be engaged in the farthest forward slot possible. To achieve a proper seal,
tighten the latch screws evenly until the unit is snug in the panel (Torque to
approximately 7 in-lbs [79N-cm]). Do not over-tighten the screws.
Installation Environment
operating temperature and provides good air circulation. Placing the unit near
devices that generate excessive heat should be avoided.
Do NOT use solvents. Continuous exposure to direct sunlight may accelerate the
aging process of the bezel.
Set-Up DIP Switches
points, backlight annunciator, and scaling. Selecting the “ON” position enables
the function.
While holding the unit in place, push the panel latch over the rear of the unit
The unit should be installed in a location that does not exceed the maximum
The bezel should be cleaned only with a soft cloth and neutral soap product.
A DIP switch is located inside the meter. It is used for the selection of decimal
Main
Circuit
Board
REAR TERMINALS
FRONT DISPLAY
S
SWITCH
JUMPER
RANGE
INPUT
1
2
3
4
5
POWER SELECTION SWITCH
WITCHES
3.62
SCALING
(92
POT
Backlight Annunciator for Units Label
SWITCHES
PANEL CUT-OUT
SET-UP
DIP
+.03
+.8
-.00
-.0
Enables the Scaling Pot
Decimal Point 1 (000.0)
Decimal Point 2 (00.00)
Decimal Point 3 (0.000)
)
FUNCTION
1.77
(45
ON
+.02
+.5
-.00
-.0
5
)
4
3
2
1