PAXLVD00 Red Lion Controls, PAXLVD00 Datasheet - Page 5

• Manufacturer Part Number: PAXLVD00
• Description: VOLTMETER DC 3 1/2-DIGIT
• Manufacturer: Red Lion Controls
• Series: PAX®LITEr
• Type: Voltmeterr

Specifications of PAXLVD00

• Measuring Range: 0 ~ 300V
• Display Style: Red Characters, Black Background
• Display Type: LED
• Display Face Size: 3.80" L x 1.95" W (96.5 x 49.5mm)
• Display Digits: 3.5
• Display Digits - Height: 0.560" (14.22mm)
• Backlight: Without
• Mounting Type: Panel Mount
• Termination: Terminal Block
• Voltage - Supply: 115VAC,230 VAC
• No. Of Digits / Alpha: 3-1/2
• Meter Function: DC Voltmeter
• Meter Range: 1.999V To 300V
• Digit Height: 14.2mm
• Power Consumption: 6VA
• Operating Temperature Range: 0°C To +60°C
• Supply Voltage Ac, Min: 115V
• Accuracy: ±0.1% %
• Connection Type: Cage-Clamp
• Cut Out, Panel: 3.62×1.77 "
• Dimensions: 4.2"L×3.8"W×1.95"H
• Display Digit Height: 0.56 "
• Display Resolution: 1 mV to 1 V
• Function: Voltage
• Meter Type: Panel
• Number Of Digits: 3-1/2
• Primary Type: Electronic
• Range, Measurement: 1.999 to 300 VDC
• Special Features: Multi-Range Unit
• Standards: CE Marked, cUL Recognized
• Temperature, Operating: 0 to 60 °C
• Voltage, Input: 1.999 to 300 V
• Voltage, Supply: 115/230 VAC
• Character Size: 0.56"
• Display Font Color: Red
• Rohs Compliant: Yes
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant, Lead free / RoHS Compliant
• Other names: RLC107

WIRING OVERVIEW
back of the meter. All conductors should conform to the meter’s voltage and
current ratings. All cabling should conform to appropriate standards of good
installation, local codes and regulations. It is recommended that power supplied
to the meter (AC) be protected by a fuse or circuit breaker.
meter case against those shown in wiring drawings for proper wire position. Strip
the wire, leaving approximately 0.3" (7.5 mm) bare lead exposed (stranded wires
should be tinned with solder). Insert the lead under the correct screw-clamp
terminal and tighten until the wire is secure. (Pull wire to verify tightness.)
EMC INSTALLATION GUIDELINES
Magnetic Interference (EMI), proper installation and wiring methods must be
followed to ensure compatibility in each application. The type of the electrical
noise, its source or the method of coupling into the unit may be different for
various installations. Listed below are some EMC guidelines for successful
installation in an industrial environment.
1. The meter should be mounted in a metal enclosure, which is properly
2. Never run Signal or Control cables in the same conduit or raceway with AC
3. Signal or Control cables within an enclosure should be routed as far away as
PAXLV Jumper Selection
3.0 W
Electrical connections are made via screw-clamp terminals located on the
When wiring the meter, compare the numbers embossed on the back of the
Although this meter is designed with a high degree of immunity to Electro-
connected to protective earth.
power lines, conductors feeding motors, solenoids, SCR controls, and
heaters, etc. The cables should be run in metal conduit that is properly
grounded. This is especially useful in applications where cable runs are long
and portable two-way radios are used in close proximity or if the installation
is near a commercial radio transmitter.
possible from contactors, control relays, transformers, and other noisy
components.
Main
Circuit
Board
REAR TERMINALS
FRONT DISPLAY
IRING THE
SELECTION
POWER
SWITCH
INPUT RANGE
JUMPER
SWITCHES
SET-UP
SCALING
DIP
POT
M
ON
ETER
5
4
3
2
1
5
4. In extremely high EMI environments, the use of external EMI suppression
5. Long cable runs are more susceptible to EMI pickup than short cable runs.
6. Switching of inductive loads produces high EMI. Use of snubbers across
devices, such as ferrite suppression cores, is effective. Install them on Signal
and Control cables as close to the unit as possible. Loop the cable through the
core several times or use multiple cores on each cable for additional protection.
Install line filters on the power input cable to the unit to suppress power line
interference. Install them near the power entry point of the enclosure. The
following EMI suppression devices (or equivalent) are recommended:
Therefore, keep cable runs as short as possible.
inductive loads suppresses EMI.
Ferrite Suppression Cores for signal and control cables:
Line Filters for input power cables:
Note: Reference manufacturer’s instructions when installing a line filter.
Snubber: RLC#SNUB0000.
Fair-Rite # 0443167251 (RLC #FCOR0000)
TDK # ZCAT3035-1330A
Steward #28B2029-0A0
Schaffner # FN610-1/07 (RLC #LFIL0000)
Schaffner # FN670-1.8/07
Corcom #1VR3
THIS AREA!
JUMPER IN
ONLY ONE
JUMPER SELECTIONS
The
INPUT RANGE JUMPER
REAR TERMINALS
indicates factory setting.
VOLT
±19.99V
±300V
±1.999V
±199.9V