PAXLIT00 Red Lion Controls, PAXLIT00 Datasheet - Page 4

• Manufacturer Part Number: PAXLIT00
• Description: METER AC CURRENT 5A 3 1/2-DIGIT
• Manufacturer: Red Lion Controls
• Series: PAX®LITEr
• Type: Ammeterr

Specifications of PAXLIT00

• Measuring Range: 0 ~ 5A
• Display Style: Red Characters, Black Background
• Display Type: LED
• Display Face Size: 3.80" L x 1.95" W (96.5 x 49.5mm)
• Display Digits: 3.5
• Display Digits - Height: 0.560" (14.22mm)
• Backlight: Without
• Mounting Type: Panel Mount
• Termination: Terminal Block
• Voltage - Supply: 115VAC,230 VAC
• No. Of Digits / Alpha: 3-1/2
• Meter Function: AC Ammeter
• Meter Range: 0A To 5A
• Digit Height: 14.2mm
• Power Consumption: 6VA
• Operating Temperature Range: 0°C To +60°C
• Supply Voltage Ac, Min: 115V
• Accuracy: ±0.5% %
• Connection Type: Cage-Clamp
• Cut Out, Panel: 3.62×1.77 "
• Dimensions: 4.2"L×3.8"W×1.95"H
• Display Digit Height: 0.56 "
• Display Resolution: 2.5 mA
• Function: Ammeter
• Meter Type: AC Current
• Number Of Digits: 3-1/2
• Primary Type: Electronic
• Range, Measurement: 0 to 5 A
• Special Features: Multi-Range Unit
• Standards: cULus Listed, CE Marked
• Temperature, Operating: 0 to 60 °C
• Voltage, Supply: 115/230 VAC
• Weight: 0.65 lbs
• Character Size: 0.56"
• Display Font Color: Red
• Rohs Compliant: Yes
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant, Lead free / RoHS Compliant
• Other names: RLC109

Installation
unit is intended to be mounted into an enclosed panel. Prepare the panel cutout
to the dimensions shown. Remove the panel latch from the unit. Slide the panel
gasket over the rear of the unit to the back of the bezel. The unit should be
installed fully assembled. Insert the unit into the panel cutout.
applying power. To access the switch, remove the meter base from the case by
firmly squeezing and pulling back on the side rear finger tabs. This should lower
the latch below the case slot (which is located just in front of the finger tabs). It
is recommended to release the latch on one side, then start the other side latch.
Power Selection Switch
Set-Up DIP Switches
points, backlight annunciator, and scaling. Selecting the “ON” position enables
the function.
1.0 I
2.0 S
BEZEL
The PAX meets NEMA 4X/IP65 requirements when properly installed. The
The meter has switches, which must be checked and/or changed prior to
A DIP switch is located inside the meter. It is used for the selection of decimal
PANEL
GASKET
proper voltage before powering the meter. The meter is shipped
from the factory in the 230 VAC position.
Caution: Insure the AC power selection switch is set for the
SWITCH
NSTALLING THE
ETTING THE
1
2
3
4
5
LATCHING
SLOTS
Backlight Annunciator for Units Label
Enables the Scaling Pot
Decimal Point 1 (000.0)
Decimal Point 2 (00.00)
Decimal Point 3 (0.000)
PANEL
FUNCTION
PANEL
MOUNTING
SCREWS
S
WITCHES
PANEL
LATCH
M
LATCHING
TABS
ETER
4
so that the tabs of the panel latch engage in the slots on the case. The panel latch
should be engaged in the farthest forward slot possible. To achieve a proper seal,
tighten the latch screws evenly until the unit is snug in the panel (Torque to
approximately 7 in-lbs [79N-cm]). Do not over-tighten the screws.
Installation Environment
operating temperature and provides good air circulation. Placing the unit near
devices that generate excessive heat should be avoided.
Do NOT use solvents. Continuous exposure to direct sunlight may accelerate the
aging process of the bezel.
While holding the unit in place, push the panel latch over the rear of the unit
The unit should be installed in a location that does not exceed the maximum
The bezel should be cleaned only with a soft cloth and neutral soap product.
Main
Circuit
Board
REAR TERMINALS
FRONT DISPLAY
POWER SELECTION
SWITCH
3.62
(92
SCALING
POT
PANEL CUT-OUT
SWITCHES
SET-UP
+.03
+.8
DIP
-.00
-.0
)
1.77
(45
ON
+.02
+.5
-.00
-.0
5
)
4
3
2
1