DS32B35-33IND# Maxim Integrated Products, DS32B35-33IND# Datasheet
DS32B35-33IND#
Specifications of DS32B35-33IND#
Available stocks
Related parts for DS32B35-33IND#
DS32B35-33IND# Summary of contents
Page 1
... Commercial and Industrial Temperature Ranges ♦ 300-mil, 20-Pin SO Package ♦ Underwriters Laboratories (UL) Recognized CC PART DS32B35-33# DS32B35-33IND# DS32C35-33# Applications DS32C35-33IND# #Denotes a RoHS-compliant device that may include lead that is exempt under RoHS requirements. The lead finish is JESD97 category e3, and is compatible with both lead-based and lead- free soldering processes. A " ...
Page 2
Accurate I C RTC with Integrated TCXO/Crystal/FRAM ABSOLUTE MAXIMUM RATINGS Voltage Range on Any Pin Relative to Ground......-0.3V to +5.0V Operating Temperature Range ..........................-40°C to +85°C Junction Temperature ......................................................+125°C Storage Temperature Range ...............................-40°C to +85°C Junction-to-Ambient Thermal Resistance (θ ...
Page 3
Accurate I ELECTRICAL CHARACTERISTICS (continued 2.7V to 3.63V -40°C to +85°C, unless otherwise noted.) (Note PARAMETER SYMBOL V Leakage Current BAT I BATLKG (V Active) CC Output Frequency Frequency Stability vs. Temperature Frequency ...
Page 4
Accurate I C RTC with Integrated TCXO/Crystal/FRAM AC ELECTRICAL CHARACTERISTICS (V = 2.7V to 3.63V -40°C to +85°C, unless otherwise noted.) (Note PARAMETER SYMBOL SCL Clock Frequency Bus Free Time Between STOP and START ...
Page 5
Accurate I POWER-SWITCH CHARACTERISTICS (T = -40°C to +85°C, Note 2, see the Power-Switch Timing diagram.) A PARAMETER SYMBOL V Fall Time PF(MAX) V PF(MIN) V Rise Time PF(MIN PF(MAX) Recovery at ...
Page 6
Accurate I C RTC with Integrated TCXO/Crystal/FRAM RST PF(MAX PF(MIN) t VCCF RST 6 _____________________________________________________________________ PB DB Pushbutton Reset Timing t RST Power-Switch Timing VCCR t REC ...
Page 7
Accurate +3.3V +25°C, unless otherwise noted STANDBY SUPPLY CURRENT vs. SUPPLY VOLTAGE 150 125 RST ACTIVE 100 2.0 2.5 3.0 3.5 4.0 V (V) CC SUPPLY CURRENT vs. TEMPERATURE ...
Page 8
... Accurate I C RTC with Integrated TCXO/Crystal/FRAM DS32B35/DS32C35 X1 OSCILLATOR AND CAPACITOR ARRAY X2 WP SCL FRAM BAT POWER CONTROL GND SCL INTERFACE AND ADDRESS REGISTER DECODE SDA 8 _____________________________________________________________________ PUSHBUTTON RESET; CONTROL LOGIC/ SQUARE-WAVE BUFFER; DIVIDER INT/SQW CONTROL CONTROL AND STATUS TEMPERATURE REGISTERS SENSOR ...
Page 9
... The devices are available in both commercial and industrial temperature ranges and is offered in a 300-mil, 20-pin SO package. The DS32B35/DS32C35 include a bank of nonvolatile memory that do not require a backup energy source to maintain the memory contents. In addition, there are no 2 ...
Page 10
... Accurate I C RTC with Integrated TCXO/Crystal/FRAM The Block Diagram shows the main elements of the DS32B35/DS32C35. The nine blocks can be grouped into six functional groups: TCXO, power control, pushbut- 2 ton function, RTC interface, and FRAM. Their opera- tions are described separately in the following sections. ...
Page 11
... See the I C Serial Data Bus section for details. Table 2. Memory Slave Address DEVICE SLAVE ADDRESS DS32B35 DS32C35 R = Read/write select bit Warning: The FRAM does not inhibit reads or writes when V is below the minimum operating voltage. CC ...
Page 12
Accurate I C RTC with Integrated TCXO/Crystal/FRAM Table 3. RTC Register Map BIT 7 ADDRESS BIT 6 BIT 5 (MSB) 00h 0 10 Seconds 01h 0 10 Minutes AM/PM 02h 0 12/24 20 Hour 03h 04h ...
Page 13
... Accurate I The DS32B35/DS32C35 contain two time-of-day/date alarms. Alarm 1 can be set by writing to registers 07h to 0Ah. Alarm 2 can be set by writing to registers 0Bh to 0Dh. The alarms can be programmed (by the alarm enable and INTCN bits of the Control register) to acti- vate the INT/SQW output on an alarm match condition. ...
Page 14
Accurate I C RTC with Integrated TCXO/Crystal/FRAM BIT 7 BIT 6 BIT 5 EOSC BBSQW CONV Special-Purpose Registers Control Register (0Eh) Bit 7: Enable Oscillator (EOSC). When set to logic 0, the oscillator is started. When set to logic ...
Page 15
Accurate I BIT 7 BIT 6 BIT 5 OSF 0 Status Register (0Fh) Bit 7: Oscillator Stop Flag (OSF). A logic 1 in this bit indicates that the oscillator either is stopped or was stopped for some period and may ...
Page 16
... BIT 5 BIT 4 BIT BIT 5 BIT 4 BIT BIT 2 BIT 1 Data Data BIT 2 BIT FRAM Address Map DS32B35 FRAM Register Map BIT 2 BIT 1 BIT 0 RANGE DS32C35 FRAM Register Map BIT 2 BIT 1 BIT 0 RANGE BIT 0 Data BIT 0 0 00–FF : 00–FF 00– ...
Page 17
... C bus and a fast mode (400kHz maximum clock rate) are defined. The DS32B35/DS32C35 work in both modes. The following bus protocol has been defined (Figure 2): • Data transfer can be initiated only when the bus is not busy. ...
Page 18
... START condition. The slave address byte contains one of the 7-bit device addresses. The slave address is 1101000 for the RTC. For the DS32B35 FRAM, the first four bits are 1010, and the next three bits select one of eight blocks of data (see Table 2). For the DS32C35 FRAM, the first seven bits are 1010000 ...
Page 19
... START condition. The slave address byte contains one of the 7-bit device addresses. The slave address is 1101000 for the RTC. For the DS32B35 FRAM, the first four bits are 1010, and the next three bits select one of eight <SLAVE ADDRESS> <R/W> ...
Page 20
... START MASTER TO SLAVE A - ACKNOWLEDGE P - STOP A - NOT ACKNOWLEDGE R/W - READ/WRITE OR DIRECTION BIT ADDRESS = D1h Figure 6. Data Read—DS32B35 FRAM Slave Transmitter Mode <SLAVE ADDRESS> <R/W> S 1010000 0 A XXXA S - START MASTER TO SLAVE A - ACKNOWLEDGE P - STOP R/W - READ/WRITE BIT Figure 7. Data Write—DS32C35 FRAM Slave Receiver Mode < ...
Page 21
... WP DS32B35/ RST DS32C35 N.C. N.C. N.C. N.C. N.C. GND PART DS32B35-33# 20 SCL DS32B35-33IND# 19 GND DS32C35-33# 18 SCL DS32C35-33IND# 17 SDA #Denotes a RoHS-compliant device that may include lead that 16 V BAT is exempt under RoHS requirements. The lead finish is JESD97 category e3, and is compatible with both lead-based and lead- ...
Page 22
... NUMBER DATE 0 12/06 Initial release Changed data sheet title/references to DS32x35 with DS32B35/DS32C35 1 1/08 Added text to the General Description section about the clock/date operation In Table 3, changed 04h range from 00–31 to 01–31 Updated the RTC descriptions in the General Description and Detailed Description ...