CS5531-ASZ Cirrus Logic Inc, CS5531-ASZ Datasheet - Page 32

• Manufacturer Part Number: CS5531-ASZ
• Description: IC ADC 16BIT 2CH W/LNA 20SSOP
• Manufacturer: Cirrus Logic Inc

Specifications of CS5531-ASZ

• Number Of Converters: 1
• Package / Case: 20-SSOP
• Number Of Bits: 16
• Sampling Rate (per Second): 3.84k
• Data Interface: Serial
• Power Dissipation (max): 45mW
• Voltage Supply Source: Analog and Digital, Dual ±
• Operating Temperature: -40°C ~ 85°C
• Mounting Type: Surface Mount
• Number Of Adc Inputs: 4
• Architecture: Delta-Sigma
• Conversion Rate: 6.25 SPs to 3840 SPs
• Resolution: 16 bit
• Input Type: Voltage
• Interface Type: Serial (3-Wire)
• Voltage Reference: 2.5 V
• Maximum Power Dissipation: 500 mW
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• Minimum Operating Temperature: - 40 C
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant, Lead free / RoHS Compliant
• Other names: 598-1111-5

2.5.6. System Calibration
For the system calibration functions, the user must
supply the converter’s calibration signals which rep-
resent ground and full scale. When a system offset
calibration is performed, a ground-referenced signal
must be applied to the converters. Figure 13 illus-
trates system offset calibration.
As shown in Figure 14, the user must input a signal
representing the positive full-scale point to perform
a system gain calibration. In either case, the cali-
bration signals must be within the specified calibra-
tion limits for each specific calibration step (refer
to the System Calibration Specifications).
2.5.7. Calibration Tips
Calibration steps are performed at the output word
rate selected by the WR2-WR0 bits of the channel
setup registers. Due to limited register lengths in
the faster word-rate filters (240 Sps and higher),
32
CM + -
0V + -
External
Connections
AIN+
AIN-
Figure 13. System Calibration of Offset
Figure 11. Self-calibration of Offset
AIN+
AIN-
+
_
1X GAIN
+
-
XGAIN
+
_
+
-
channels that are used at these rates should also be
calibrated in one of these word rates, and channels
used in the lower word rates (120 Sps and lower)
should be calibrated at one of these lower rates.
Since higher word rates result in conversion words
with more peak-to-peak noise, calibration should
be performed at the lowest possible output word
rate for maximum accuracy. For the 7.5 Sps to 120
Sps word rate settings, calibrations can be per-
formed at 7.5 Sps, and for 240 Sps and higher, cal-
ibration can be performed at 240 Sps. To minimize
digital noise near the device, the user should wait
for each calibration step to be completed before
reading or writing to the serial port. Reading the
calibration registers and averaging multiple cali-
brations together can produce a more accurate cal-
ibration result. Note that accessing the ADC’s
serial port before a calibration has finished may re-
sult in the loss of synchronization between the mi-
Full Scale + -
Reference
CM + -
Figure 14. System Calibration of Gain
Figure 12. Self-calibration of Gain
External
Connections
+
-
VREF+
VREF-
AIN+
AIN-
AIN+
AIN-
CS5531/32/33/34-AS
+
-
+
-
XGAIN
XGAIN
CLOSED
CLOSED
OPEN
OPEN
DS289F5
+
-
+
-