AD7734BRUZ Analog Devices Inc, AD7734BRUZ Datasheet - Page 22

• Manufacturer Part Number: AD7734BRUZ
• Description: IC ADC 24BIT 4-CH 28-TSSOP
• Manufacturer: Analog Devices Inc

Specifications of AD7734BRUZ

• Data Interface: DSP, MICROWIRE™, QSPI™, Serial, SPI™
• Number Of Bits: 24
• Sampling Rate (per Second): 15.4k
• Number Of Converters: 1
• Power Dissipation (max): 100mW
• Voltage Supply Source: Analog and Digital
• Operating Temperature: -40°C ~ 105°C
• Mounting Type: Surface Mount
• Package / Case: 28-TSSOP (0.173", 4.40mm Width)
• Resolution (bits): 24bit
• Sampling Rate: 15.4kSPS
• Input Channel Type: Single Ended
• Supply Voltage Range - Analog: 4.75V To 5.25V
• Supply Current: 13.5µA
• Number Of Elements: 1
• Resolution: 24Bit
• Architecture: Delta-Sigma
• Sample Rate: 3.05MSPS
• Input Polarity: Unipolar/Bipolar
• Input Type: Voltage
• Rated Input Volt: 5/10/±5/±10V
• Differential Input: No
• Power Supply Requirement: Analog and Digital
• Single Supply Voltage (typ): 5V
• Single Supply Voltage (min): 4.75V
• Single Supply Voltage (max): 5.25V
• Dual Supply Voltage (typ): Not RequiredV
• Dual Supply Voltage (min): Not RequiredV
• Dual Supply Voltage (max): Not RequiredV
• Power Dissipation: 100mW
• Integral Nonlinearity Error: ±0.0045%FSR
• Operating Temp Range: -40C to 105C
• Operating Temperature Classification: Industrial
• Mounting: Surface Mount
• Pin Count: 28
• Package Type: TSSOP
• Input Signal Type: Single-Ended
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: EVAL-AD7734EBZ - BOARD EVALUATION FOR AD7734
• Lead Free Status / Rohs Status: Compliant

AD7734
DIGITAL INTERFACE DESCRIPTION
Hardware
The AD7734 serial interface can be connected to the host device
via the serial interface in several different ways.
The CS pin can be used to select the AD7734 as one of several
circuits connected to the host serial interface. When CS is high,
the AD7734 ignores the SCLK and DIN signals and the DOUT
pin goes to the high impedance state. When the CS signal is not
used, connect the CS pin to DGND.
The RDY pin can be polled for high-to-low transition or can
drive the host device interrupt input to indicate that the
AD7734 has finished the selected operation and/or new data
from the AD7734 is available. The host system can also wait a
designated time after a given command is written to the device
before reading. Alternatively, the AD7734 status can be polled.
When the RDY pin is not used in the system, it should be left as
an open circuit. (Note that the RDY pin is always an active
digital output, i.e., it never goes into a high impedance state.)
Figure 14. AD7734 to Host Device Interface, DSP
Figure 13. AD7734 to Host Device Interface, SPI
AD7734
AD7734
RESET
DOUT
SCLK
RESET
RDY
DOUT
DIN
SCLK
CS
RDY
DIN
CS
DV
DGND
DV
DD
DD
DV
DD
ADSP-2105
SCLK
DR
DT
INT
TFS
RFS
68HC11
SS
SCK
MISO
MOSI
INT
Rev. 0 | Page 22 of 32
The RESET pin can be used to reset the AD7734. When not
used, connect this pin to DV
The AD7734 interface can be reduced to just two wires
connecting the DIN and DOUT pins to a single bidirectional
data line. The second signal in this 2-wire configuration is the
SCLK signal. The host system should change the data line
direction with reference to the AD7734 timing specification
(see the Bus Relinquish Time in Table 2). The AD7734 cannot
operate in the continuous read mode in 2-wire serial interface
configuration.
All the digital interface inputs are Schmitt-Triggered; therefore,
the AD7734 interface features higher noise immunity and can
be easily isolated from the host system via optocouplers.
Figure 13, Figure 14, and Figure 15 outline some of the possible
host device interfaces: SPI without using the CS signal
(Figure 13), a DSP interface (Figure 14), and a 2-wire
configuration (Figure 15).
Figure 15. AD7734 to Host Device Interface, 2-Wire Configuration
AD7734
RESET
DOUT
SCLK
DIN
CS
DGND
DV
DD
DD
.
P3.1/TXD
P3.0/RXD
8xC51