HI5714/7CB-T Intersil, HI5714/7CB-T Datasheet - Page 9
![no-image](/images/manufacturer_photos/0/3/341/intersil_sml.jpg)
HI5714/7CB-T
Manufacturer Part Number
HI5714/7CB-T
Description
CONV A/D 8BIT 75MSPS 24-SOIC
Manufacturer
Intersil
Datasheet
1.HI57144CBZ.pdf
(14 pages)
Specifications of HI5714/7CB-T
Number Of Bits
8
Sampling Rate (per Second)
75M
Data Interface
Parallel
Number Of Converters
1
Power Dissipation (max)
375mW
Voltage Supply Source
Analog and Digital
Operating Temperature
0°C ~ 70°C
Mounting Type
Surface Mount
Package / Case
24-SOIC (0.300", 7.50mm Width)
Lead Free Status / RoHS Status
Contains lead / RoHS non-compliant
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Part Number:
HI5714/7CB-T
Manufacturer:
HAR
Quantity:
20 000
Detailed Description
Theory of Operation
The HI5714 design utilizes a folding and interpolating
architecture. This architecture reduces the number of
comparators, reference taps, and latches, thereby reducing
power requirements, die size and cost.
subranging converter by using 2 lower resolution converters
to do a course and subranged fine conversion. A more
complete description is given in the application note “Using
the HI5714 Evaluation Module” (AN9517).
Reference Input, V
The HI5714 requires an external reference to be connected
to pins 4 and 9, V
It is recommended that adequate high frequency decoupling
be provided at the reference input pin in order to minimize
overall converter noise. A 0.1µF and a 1nF capacitor as
close as possible to the reference pins work well.
V
within 1.2V to 1.6V. If the reference voltages go outside their
respective ranges, the input folding amplifiers may saturate
giving erroneous digital data. The range for (V
1.9V to 2.7V, which defines the analog input range.
Digital Control and Clock Requirements
The HI5714 provides a standard high-speed interface to
external TTL logic families.
The outputs can be three-stated by setting the OE input (pin
22) high.
The clock input operates at standard TTL levels as well as a
low level sine wave around the threshold level. The HI5714
can operate with clock frequencies from DC to 75MHz. The
clock duty cycle should be 50% ±10% to ensure rated
performance. Duty cycle variation, within the specified
range, has little effect on performance. Due to the clock
speed it is important to remember that clock jitter will affect
the quality of the digital output data.
The clock can be stopped at any time and restarted at a later
time. Once restarted the digital data will be valid at the
second rising edge of the clock plus the data delay time.
Digital Outputs and O/UF Output
The digital outputs are standard TTL type outputs. The
HI5714 can drive 1 to 3 TTL inputs depending on the input
current requirements.
Should the analog input exceed the top or bottom reference
the over/underflow output (pin 11) will go high. Should the
analog input exceed the top reference voltage, V
digital outputs will remain at all 1s until the analog input goes
below V
A folding A/D converter operates basically like a 2 step
RT
must be kept within the range of 3.5V to 3.9V and V
RT
. Also, should the analog input go below the
RB
and V
RT
and V
RT
.
9
RB
RT
RT
- V
, the
RB
) is
RB
HI5714
bottom reference voltage, V
remain at all 0s until the analog input goes above V
Analog Input
The analog input will accept a voltage within the reference
voltage levels, V
is specified in the Electrical Specifications table.
The analog input is relatively high impedance (10kΩ) but
should be driven from a low impedance source. The input
capacitance is low (14pF) and there is little kickback from the
input, so a series resistance is not necessary but it may help
to prevent the driving amplifier from oscillating.
The input bandwidth is typically 18MHz. Exceeding 18MHz
will result in sparkle at the digital outputs. The bandwidth
remains constant at clock rates up to 75MHz.
Supply and Ground Considerations
In order to keep digital noise out of the analog signal path,
the HI5714 has separate analog and digital supply and
ground pins. The part should be mounted on a board that
provides separate low impedance connections for the analog
and digital supplies and grounds.
The analog and digital grounds should be tied together at
one point near the HI5714. The grounds can be connected
directly, through an inductor (ferrite bead), or a low valued
resistor. DGND and AGND can be tied together. To help
minimize noise, tie pin 5 (NC) to AGND and pins 3 (NC) and
10 (NC) to DGND.
For best performance, the supplies to the HI5714 should be
driven by clean, linear regulated supplies. The board should
also have good high frequency leaded decoupling capacitors
mounted as close as possible to the converter. Capacitor
leads must be kept as short as possible (less than
total length). A 0.1µF and a 1nF capacitor as close as
possible to the pin works well. Chip capacitors will provide
better high frequency decoupling but leaded capacitors
appear to be adequate.
If the part is to be powered by a single supply, then the
analog supply pins should be isolated by ferrite beads from
the digital supply pins. This should help minimize noise on
the analog power pins.
Refer to Application Note AN9214, “Using Intersil High
Speed A/D Converters”, for additional considerations when
using high speed converters.
Increased Accuracy
Further calibration of the ADC can be done to increase
absolute level accuracy. First, a precision voltage equal to
the ideal VIN
until the 0 to 1 transition occurs on the digital output. Next, a
voltage equal to the ideal VIN
V
the digital output.
RT
is then adjusted until the 254 to 255 transition occurs on
-FS
RB
+ 0.5 LSB is applied at V
and V
RT
RB
, minus some offset. The offset
+FS
, the digital outputs will
- 1.5 LSB is applied at V
IN
. Adjust V
1
RT
/
2
RB
.
inch
IN
.