CS4353-CNZ Cirrus Logic Inc, CS4353-CNZ Datasheet - Page 11

• Manufacturer Part Number: CS4353-CNZ
• Description: IC DAC STER 106DB 2VRMS 24QFN
• Manufacturer: Cirrus Logic Inc

Specifications of CS4353-CNZ

• Number Of Converters: 1
• Package / Case: 24-QFN
• Number Of Bits: 24
• Data Interface: Serial
• Voltage Supply Source: Single Supply
• Power Dissipation (max): 152mW
• Operating Temperature: -40°C ~ 85°C
• Mounting Type: Surface Mount
• Number Of Dac Outputs: 2
• Resolution: 24 bit
• Interface Type: Serial
• Supply Voltage (max): 3.47 V
• Supply Voltage (min): 3.13 V
• Maximum Operating Temperature: + 125 C
• Mounting Style: SMD/SMT
• Maximum Power Dissipation: 152 mW
• Minimum Operating Temperature: - 55 C
• Supply Current: 10 mA
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: 598-1519 - BOARD EVAL FOR CS4353 DAC
• Settling Time: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant
• Other names: 598-1640

DS803F1
DC ELECTRICAL CHARACTERISTICS
Test conditions (unless otherwise specified): VCP = VA = VL = 3.3 V; AGND = DGND = CPGND = 0 V; SDIN = 0;
all voltages with respect to ground.
Notes: 15. Current consumption increases with increasing sample rate and increasing MCLK frequency. Typical
2.1
Power Supplies
Power Supply Current
Power Dissipation (All Supplies)
(Note 15)
Power Supply Rejection Ratio
DC Output Voltages
Pin Voltage
16. Power-down is defined as RESET pin = Low with all clock and data lines held static low. All digital inputs
17. Valid with the recommended capacitor value on VBIAS as shown in the typical connection diagram in
18. Typical voltage shown for “Initialization State”, see
Digital I/O Pin Characteristics
Input and output levels and associated power supply voltage are shown in
exceed the corresponding power supply voltage.
Pin Name
1_2VRMS
values are based on Fs = 48 kHz and MCLK = 12.288 MHz. Maximum values are based on highest
sample rate and highest MCLK frequency; see
ance between speed modes is small.
have a weak pull-down (approximately 50 kΩ) which is only present during reset. Opposing this pull-
down will slightly increase the power-down current.
Section
during normal operation.
RESET
MCLK
LRCK
SCLK
I²S/LJ
SDIN
DEM
3.
(Note 15)
Power Supply
Parameters
(Note 17)
Power-Down, All Supplies
VL
Normal Operation, 1_2VRMS = 0
Table 1. Digital I/O Pin Characteristics
VFILT+ to GND
GND to VFILT-
Power-Down
Normal Operation
Input
Input
Input
Input
Input
Input
Input
Input
FLYN+ to FLYN-
FLYP+ to FLYP-
I/O
VA to VBIAS
(Note 16)
(Note 16)
(Note 18)
(Note 18)
(1 kHz)
(60 Hz)
Switching Specifications - Serial Audio
Section
Symbol
PSRR
Driver
I
VCP
I
I
I
PD
VA
VL
-
-
-
-
-
-
-
-
4.8. Typical voltage may be up to 1.5 V lower
Min
-
-
-
-
-
-
-
-
-
-
-
-
-
Table
0.9 V - 3.3 V, with Hysteresis
Typ
127
2.4
0.1
3.3
6.6
6.6
6.6
2.1
36
65
60
60
1
1. Logic levels should not
0.9 V - 3.3 V
0.9 V - 3.3 V
0.9 V - 3.3 V
0.9 V - 3.3 V
0.9 V - 3.3 V
0.9 V - 3.3 V
0.9 V - 3.3 V
Receiver
Max
152
0.2
43
3
-
-
-
-
-
-
-
-
-
Interface. Vari-
CS4353
Units
mW
mW
mA
mA
mA
μA
dB
dB
V
V
V
V
V
11